Chevrolet Bolt EUV 2023 Windshield Replacement User Guide
Windshield Replacement
Front Wiper Blade Replacement
Windshield wiper blades should be replaced periodically. See the Maintenance Schedule 0 293. Replacement blades come in different types and are removed in different ways. For proper type and length, see Maintenance Replacement Parts 0 296.
Caution
Allowing the wiper arm to touch the windshield when no wiper blade is installed could damage the windshield. Any damage that occurs would not be covered by the vehicle warranty. Do not allow the wiper arm to touch the windshield.
To replace the windshield wiper blade:
- Pull the windshield wiper assembly away from the windshield
- Press the button in the middle of the wiper arm connector, and pull the wiper blade away from the arm connector.
- Remove the wiper blade.
- Reverse Steps 1–3 for wiper blade replacement.
Rear Wiper Blade Replacement
The rear wiper blade and wiper arm have a cover for protection. The cover must be removed before the wiper blade can be replaced.
To remove the cover:
- Slide a plastic tool under the cover and push upward to unsnap.
- Slide the cover toward the wiper blade tip to unhook it from the blade assembly.
- Remove the cover.
- After the wiper blade replacement, ensure that the cover hook slides into the slot in the blade assembly.
- Snap the cover down to secure it.
To replace the wiper blade:
- Lift the wiper arm away from the windshield.
- Push the release lever (2) to disengage the hook and push the wiper arm (1) out of the blade assembly (3).
- Push the new blade assembly securely on the wiper arm until the release lever clicks into place.
- Replace the wiper cover.
Windshield Replacement
Driver Assistance Systems
If the windshield needs to be replaced and the vehicle is equipped with a front camera sensor for the Driver Assistance Systems, a GM replacement windshield is recommended. The replacement windshield must be installed according to GM specifications for proper alignment. If it is not, these systems may not work properly, they may display messages, or they may not work at all. See your dealer for proper windshield replacement.
Gas Strut(s)
Your vehicle may be equipped with a gas strut(s) to provide assistance in lifting and holding open the hood/trunk/liftgate system in the fully open position.
Warning
If the gas struts that hold open the hood, trunk, and/or liftgate fail, you or others could be seriously injured. Take the vehicle to your dealer for service immediately. Visually inspect the gas struts for signs of wear, cracks, or other damage periodically. Check to make sure the hood/trunk/liftgate is held open with enough force. If struts are failing to hold the hood/trunk/liftgate, do not operate. Has the vehicle been serviced?
Caution
Do not apply tape or hang any objects from gas struts. Also do not push down or pull on gas struts. This may cause damage to the vehicle. See Maintenance Schedule 0 293.
Hood
Trunk
Liftgate
Headlamp Aiming
Front Headlamp Aiming
Headlamp aim has been preset and should need no further adjustment If the vehicle is damaged in a crash, the headlamp aim may be affected. If an adjustment to the headlamps is necessary, see your dealer.
Bulb Replacement
For the proper type of replacement bulbs, or any bulb changing procedure not listed in this section, contact your dealer.
Caution
Do not replace incandescent bulbs with aftermarket LED replacement bulbs. This can cause damage to the vehicle’s electrical system.
Halogen Bulbs
Warning
Halogen bulbs have pressurized gas inside and can burst if you drop or scratch the bulb. You or others could be injured. Be sure to read and follow the instructions on the bulb package.
LED Lighting
This vehicle has several LED lamps. For replacement of any LED lighting assembly, contact your dealer.
Back-Up Lamps
To access the bulbs, reach up behind the rear bumper. To replace one of these bulbs:
- Turn the bulb socket counterclockwise and pull the bulb straight out of the socket.
- Press the new bulb into the socket.
- Turn the bulb socket clockwise to reinstall.
Electrical System
High Voltage Devices and Wiring
Warning
Exposure to high voltage can cause shock, burns, and even death. The high-voltage components in the vehicle can only be serviced by technicians with special training. High-voltage components are identified by labels. Do not remove, open, take apart, or modify these components. High voltage cable or wiring has orange covering or labels. Do not probe, tamper with, cut, or modify high-voltage cables or wiring.
Electrical System Overload
The vehicle has fuses and circuit breakers to protect against an electrical system overload. When the current electrical load is too heavy, the circuit breaker opens and closes, protecting the circuit until the current load returns to normal or the problem is fixed. This greatly reduces the chance of circuit overload and fire caused by electrical problems. Fuses and circuit breakers protect power devices in the vehicle.
If there is a problem on the road and a fuse needs to be replaced, the same amperage fuse can be borrowed. Choose some feature of the vehicle that is not needed to use and replace them as soon as possible. To check a fuse, look at the band inside the fuse. If the band is broken or melted, replace the fuse. Be sure to replace a bad fuse with a fuse of identical size and rating.
Chevrolet Bolt EUV 2023 Top Accessories
[amalinkspro_table id=”32452″ new-window=”on” nofollow=”on” addtocart=”off” /]
Reference Links
View Full User Guide: Chevrolet Bolt EUV 2023 User
Download Manuals: https://www.chevrolet.com/support/vehicle/manuals-guides
