Table of Contents

Suzuki New ERTIGA 2020 Installation with Lap-Shoulder User Manual

Installation with Lap-Shoulder

CAUTION
If your vehicle is equipped with the head restraint, adjust the height of the head restraint or remove it for fitting the child restraint, as necessary. However, if a booster cushion not equipped with the seatback is fitted, the seat head restraint should not be removed. If the head restraint is removed for fitting the child restraint, you need to install it again after removing the child restraint. If the child restraint is fitted improperly, a child sitting in it could be injured in a collision.

NOTE:
Stow the removed head restraint in the luggage compartment so it will not cause inconvenience to the occupants.

ELR type belt

Whenever possible, SUZUKI recommends that child restraint systems be installed on the 2nd-row seat. According to accident statistics, children are safer when properly restrained in rear seating positions than in front seating positions.

If you must install the child restraint system on the front passenger’s seat, follow the instructions below.
- - Slide the seat to the rear position by the seat position adjustment lever.
  - If there is a gap or space between the child restraint and the seatback, adjust the seatback angle in order to install the child restraint system properly.

Install your child restraint system according to the instructions provided by the child restraint system manufacturer. Check that the seat belt is securely latched.
Move the child restraint system in all directions to check that it is securely installed. When you put your child in the child restraint system, appropriately slide the front seat forward not to touch a part of your child’s body.

Installation with ISOFIX Type Anchorages

Your vehicle is equipped with the lower anchorages in the 2nd-row seat outboard seating positions for securing ISOFIX type of child restraints with the connecting bars. The lower anchorages are located where the rear of the seat cushion meets the bottom of the seatback.

WARNING
Install the ISOFIX type of child restraint(s) in the only outboard seating positions, not in the central position for the 2nd-row seat. Install the ISOFIX-type child restraint system according to the instructions provided by the child restraint system manufacturer. After installation, try moving the child restraint system in all directions especially forward to check that connecting bars are securely latched to the anchorages.

Your vehicle is equipped with the top tether anchorages. Use the top tether strap of the child restraint according to the instructions provided by the child restraint system manufacturer.

Here is a general instruction:

NOTE:
Stow the removed head restraint in the luggage compartment so it will not cause inconvenience to the occupants.

Place the child restraint in the 2nd row seat, inserting the connecting bars to the anchorages between the seat cushion and the seatback.
Use your hands to carefully align the connecting bar tips with the anchor-ages. Take care not to pinch your fingers.
Grasp the front of the child restraint and push the child restraint forcefully to latch the connecting bars.
Check that they are securely latched by trying to move the child restraint system in all directions, especially forward.
Attach the top tether strap referring to the “Installation of the child restraint with top tether” section.
When you put your child in the child restraint system, appropriately slide the front seat forward not to touch a part of your child’s body.
Push the child restraint toward the anchor-ages so that the connecting bar tips are partially hooked to the anchorages. Use your hands to confirm the position.
NOTICE
When installing a child restraint system to the 2nd-row seat, slide the seat installed the child restraint system as far back as possible.

Installation of Child Restraint with Top Tether

NOTE:
Stow the removed head restraint in the luggage compartment so it will not cause inconvenience to the occupants.

Some child restraint systems require the use of a top tether strap. Top tether anchor-age brackets are provided in your vehicle at the locations shown in the illustrations. The number of the top tether anchorage brackets provided in your vehicle depends on the vehicle’s specification. Install the child restraint system as follows:

Secure the child restraint on the 2nd-row seat using the procedure described above for securing a restraint system that does not require a top tether strap.
Hook the top tether strap to the top tether anchorage bracket and tighten the top tether strap according to the instructions provided by the child restraint system manufacturer. Attach the top tether strap to the corresponding top tether anchorage bracket located directly behind the child restraint.
When routing the top tether strap, pass the top tether strap as shown in the illustration. (Refer to the “Head restraints” section for details on how to adjust the height of the head restraint or remove it.)
Check that cargo does not interfere with the routing of the top tether strap.

NOTICE
When installing a child restraint system to the 2nd-row seat, slide the seat installed to the child restraint system as far back as possible.

Reference Links

View Full User Guide: Suzuki New ERTIGA 2020 User Manual

Download Manuals: https://suzuki-aftersales.net/manuals