2024 Dodge Hornet Fuses and Fuse Box Diagram User Guide
Discover the 2024 Dodge Hornet fuse box layout and detailed fuse diagram. Understanding where each fuse is, how it protects electrical systems, and how to inspect or replace it helps owners diagnose and maintain vehicle performance.
2024 Dodge Hornet Specs, Price, Features, Mileage And Review
Video: 2024 Dodge Hornet Fuses
Dodge FUSES Guide
General Information
WARNING!
- When replacing a blown fuse, always use an appropriate replacement fuse with the same amp rating as the original fuse. Never replace a fuse with another fuse of a higher amp rating. Never replace a blown fuse with metal wires or any other material. Do not place a fuse inside a circuit breaker cavity or vice versa. Failure to use proper fuses may result in serious personal injury, fire and/or property damage.
- Before replacing a fuse, make sure that the ignition is off and that all the other services are switched off and/or disengaged.
- If the replaced fuse blows again, contact an authorized dealer.
- If a general protection fuse for safety systems (air bag system, braking system), power unit systems (engine system, transmission system) or steering system blows, contact an authorized dealer.
The fuses protect electrical systems against excessive current.
When a device does not work, you must check the fuse element inside the blade fuse for a break/melt.
Also, please be aware that using power outlets for extended periods with the engine off may result in vehicle battery discharge.
- Fuse Element
- Blade Fuse with a good/functional fuse element
- Blade Fuse with a bad/not functional fuse element (blown fuse)
Power Distribution Center/Fuses And Relays
The Front Power Distribution Center is located in the engine compartment. This module contains fuses and relays. Fuse cavity locations are printed on the inside of the power distribution centre cover.
CAUTION!
When installing the power distribution centre cover, it is important to ensure the cover is properly positioned and fully latched. Failure to do so may allow water to get into the power distribution centre and possibly result in an electrical system failure.
The fuse box screw and cover must be removed to gain access to the fuses.
For fuse box access, proceed as follows:
- Turn the locking screw counterclockwise.
- Slowly release the screw.
- Remove the fuse box cover by sliding it upward.
- Reverse the procedure to reinstall.
Underhood Power Distribution Location
Fuse Box Cover And Locking Screw Removal
- Fuse Cover
- Locking Screw
Fuse Box Diagram
| Cavity | Cartridge Fuse | Maxi Fuse | Mini Fuse | Description |
| * If Equipped | ||||
| F01 | – | 70 Amp Tan | – | BCM1 |
| F02 | – | 70 Amp Tan | – | BCM2 / RDU |
| F03 | 20 Amp Blue | – | – | BCM3 |
| F04 | 40 Amp Green | – | – | BCM Valves |
| F05 | – | 40 Amp Orange | – | PTC 1 |
| F06 | – | 20 Amp Yellow | – | Front Wiper Motor |
| F07 | – | 20 Amp Yellow | – | DTCM |
| F08 | 30 Amp Pink | – | – | Power Supply F24 – F87 – Fxx |
| F09 | – | – | 7.5 Amp Brown | ECM T09 |
| F10 | – | – | 15 Amp Blue | Horn |
| F11 | – | – | 5 Amp Tan | Engine Secondary Loads |
| F14 | – | – | 7.5 Amp Brown | LTR |
| F15 | – | 40 Amp Orange | – | BSM Pump |
| F16 | – | – | 10 Amp Red | ECM / TCM / AGSM |
| F17 | – | – | 10 Amp Red | Engine Primary Loads |
| F18 | – | – | 5 Amp Tan | IGNM |
| F19 | – | – | 7.5 Amp Brown | A/C Compressor |
| F20 | – | – | 15 Amp Blue | Rear Cargo Outlet |
| F21 | – | – | 20 Amp Yellow | Fuel Pump |
| F22 | – | – | 15 Amp Blue | ECM |
| F23 | – | – | 5 Amp Tan | USB / Aux Outlet |
| F24 | – | – | 10 Amp Red | DTCM |
| F30 | – | – | 5 Amp Tan | AWD DTCM |
| F81 | – | 30 Amp Green | – | Brake Booster Vacuum Pump |
| F82 | – | – | – | Spare |
| F82 | 40 Amp Green | – | – | External Oil Pump * |
| F83 | 40 Amp Green | – | – | HVAC Fan |
| F84 | – | – | 7.5 Amp Brown | Rad Fan Enable |
| F87 | – | – | 5 Amp Tan | AGSM |
| F88 | – | – | 7.5 Amp Brown | Heated Mirrors & Washer Nozzle |
| F89 | 30 Amp Pink | – | – | Rear Window Defrost |
| F90 | – | – | 5 Amp Tan | Intelligent Battery Sensor |
| F01 | – | 70 Amp Tan | – | BCM1 |
| F02 | – | 70 Amp Tan | – | BCM2 / RDU |
| F03 | 20 Amp Blue | – | – | BMC3 |
| F04 | 40 Amp Green | – | – | BCM Valves |
| F05 | – | 40 Amp Orange | – | PTC 1 |
| F06 | – | 20 Amp Yellow | – | Front Wiper Motor |
| F07 | – | 50 Amp Red | – | AUX 1 RDU |
| F08 | 30 Amp Pink | – | – | Power Supply F24 – F87 – Fxx |
| F09 | – | – | 7.5 Amp Brown | ECM T09 |
| F10 | – | – | 15 Amp Blue | Horn |
| F11 | – | – | 5 Amp Tan | Engine Secondary Loads |
| F14 | – | – | 7.5 Amp Brown | LTR |
| F15 | – | 70 Amp Tan | – | BSM Pump |
| F16 | – | – | 10 Amp Red | ECM / TCM / AGSM |
| F17 | – | – | 10 Amp Red | Engine Primary Loads |
| F18 | – | – | 5 Amp Tan | IGNM * |
| F19 | – | – | 7.5 Amp Brown | A/C Compressor |
| F20 | – | – | 15 Amp Blue | Rear Cargo Outlet |
| F21 | – | – | 20 Amp Yellow | Fuel Pump |
| F22 | – | – | 20 Amp Yellow | Engine Primary Loads |
| F23 | – | – | 5 Amp Tan | USB / Aux Outlet |
| F24 | – | – | 10 Amp Red | TCM |
| F30 | – | – | – | Spare |
| F81 | – | 40 Amp Orange | – | AUX 2 RDU |
| F82 | 40 Amp Green | – | – | External Oil Pump (AT) |
| F83 | 40 Amp Green | – | – | HVAC Fan |
| F84 | – | – | 7.5 Amp Brown | Rad Fan Enable |
| F87 | – | – | 5 Amp Tan | AGSM |
| F88 | – | – | 7.5 Amp Brown | Heated Mirrors & Washer Nozzle |
| F89 | 30 Amp Pink | – | – | Rear Window Defrost |
| F90 | – | – | 5 Amp Tan | Intelligent Battery Sensor |
| Fxx | – | – | 25 Amp Clear | PIM |
Fuse Box Diagram
Supplemental Fuse Box
| Cavity | Mini Fuse | Description |
| F01 | 5 Amp Tan | Electric Air Heater (EAH) |
| F02 | 7.5 Amp Brown | Electric Air Compressor (EAC) |
| F03 | 5 Amp Tan | Integrated Dual Charge Module (IDCM) |
| F04 | 5 Amp Tan | Charge Port Indicator Module (CPIM) |
| F05 | 15 Amp Blue | Power Electronic Coolant Pump 2 (PECP2) |
| F06 | 15 Amp Blue | Power Electronic Coolant Pump (PECP) |
| F07 | 5 Amp Tan | Aux Heater Pump (AHP) |
| F08 | 5 Amp Tan | PIM Feed 1 |
| F09 | 10 Amp Red | BPCM Feed 1 |
| F10 | 5 Amp Tan | PIM Feed 3 |
| F11 | 10 Amp Red | BPCM Feed 2 |
| F12 | 5 Amp Tan | Electronic Pedestrian Protection Module (EPPM) |
Relays
| Cavity | Maxi Fuse | Mini Fuse | Description |
| T02 | – | – | Not Used |
| T03 | – | 30 Amp | Horn |
| T05 | – | 30 Amp | A/C Compressor |
| T06 | – | 30 Amp | Rad Fan Enable |
| T07 | 50 Amp | – | Aux.1 / DTCM |
| T08 | – | 30 Amp | HVAC Fan |
| T09 | – | 30 Amp | Engine Main Relay |
| T10 | – | – | Not Used |
| T14 | – | 30 Amp | Rear Cargo Power Outlet |
| T17 | – | 30 Amp | Rear Window Defrost/Heated Mirrors |
| T19 | – | – | Not Used |
| T20 | – | 30 Amp | Starter Relay R1 |
| T31 | – | 30 Amp | Fuel Pump |
| T89 | – | – | Not Used |
| T90 | – | 30 Amp | Brake Booster Vacuum Pump |
Relays
| Cavity | Maxi Fuse | Mini Fuse | Description |
| T02 | – | – | Not Used |
| T03 | – | 30 Amp | Horn |
| T05 | – | 30 Amp | A/C Compressor |
| T06 | – | 30 Amp | Rad Fan Enable |
| T07 | 50 Amp | – | Aux.1 |
| T08 | – | 30 Amp | HVAC Fan |
| T09 | – | 30 Amp | Engine Main Relay |
| T10 | – | – | Not Used |
| T14 | – | 30 Amp | Rear Cargo Power Outlet |
| T17 | – | 30 Amp | Rear Window Defrost/Heated Mirrors |
| T19 | – | 30 Amp | External Oil Pump |
| T20 | – | 30 Amp | Starter Relay R1 |
| T31 | – | 30 Amp | Fuel Pump |
| T89 | – | – | Not Used |
| T90 | – | 30 Amp | Brake Booster Vacuum Pump |
Interior Fuses
The interior fuse panel is located under the driver’s side lower instrument panel.
Fuse Box Diagram
| Cavity | Mini Fuse | Description |
| *If Equipped | ||
| F31 | 7.5 Amp Brown | HVAC Relay Coil & Power Outlet / Seat Relay Coil |
| F33 | 20 Amp Yellow | Front Passenger Window Lifter |
| F34 | 20 Amp Yellow | Front Driver Window Lifter |
| F36 | 15 Amp Blue | HVAC / VTA / External Mirror /Ceiling Light / CVPM / Radio Mod / USB / AUX/ DCSD / Electric Steering Lock |
| F37 | 10 Amp Red | Brake Switch / DASM / IPC |
| F38 | 20 Amp Yellow | Door Lock & Unlock / Liftgate Release |
| F42 | 7.5 Amp Brown | Brake System Module, Electric Power Steering |
| F43 | 20 Amp Yellow | Bi-Directional Washer Pump |
| F47 | 20 Amp Yellow | The Rear Left Window Lifter |
| F48 | 20 Amp Yellow | Rear Right Window Lifter |
| F49 | 7.5 Amp Brown | Park Assist, Blind Spot, Voltage Stabilizer, Humidity Sensor, Electronic Steering Lock, Temp Sense, Mirror, Heated Seats, Light And Rain Sensor, Start Stop Switch |
| F50 | 7.5 Amp Brown | Occupant Restraint Controller |
| F51 | 7.5 Amp Brown | Electronic Climate Control, Occupant Classification, Rear View Camera, Climate Control, Headlamp Leveling, Terrain Select, Heated Rear Window, Trailer Tow, Haptic Lane Mod |
| F53 | 7.5 Amp Brown | HCP / Reverse Gear / ISNSR / A/C Compressor / HVAC / Defrosting / Right & Left Headlamp Leveling / LDW / Alarm Mod / Psg Airbag / Trailer Tow Mod / AFLM / Air Quality Sensor / ASBM |
| F94 | 15 Amp Blue | Power Outlet |
2024 Dodge Hornet Specs, Price, Features, Mileage And Review
Rear Cargo Fuse/Relay Distribution Unit — If Equipped
To access the fuses, remove the access door from the left rear panel in the rear cargo area.
The fuses may be contained in two units. Fuse Holder No. 1 is located closest to the rear of the vehicle and Fuse Holder No. 2 (If equipped with trailer towing) is located closest to the front of the vehicle.
- Fuse Holder No. 1
- Fuse Holder No. 2
Fuse Box Diagram
Fuse Holder No. 1
| Cavity | Mini Fuse | Description |
| * If Equipped | ||
| F1 | 20 Amp Yellow | Sunroof* |
| F2 | – | – |
| F3 | 30 Amp Green | Power Liftgate Module (PLGM) |
| F4 | 5 Amp Tan | Driver And Passenger Ventilated Seats (HMSM*) |
| F5 | 25 Amp Clear | Heating And Memory Drive Seat Module 1 |
| F6 | 10 Amp Red | Heating And Memory Drive Seat Module 2 |
| F7 | 7.5 Amp Brown | Driver And Passenger Lumbar Regulator (Without HMSM) |
| F8 | 20 Amp Yellow | Passenger Seat SW (HMSM*) |
Fuse Holder No. 2
| Cavity | Mini Fuse | Description |
| F3 | 5 Amp Tan | Hands-Free Power Liftgate (HFRM) |
| F4 | 7.5 Amp Brown | Damping Control Module |
| F5 | 5 Amp Tan | Changeover Valve Feed (ELCM) |
| F8 | 7.5 Amp Brown | Damping Control Module |
On the Rear Cargo Fuse/Relay Distribution Unit bracket, there is a Maxi Fuse holder for the Amplifier (if equipped).
| Cavity | Maxi Fuse | Description |
| * If Equipped | ||
| F01 | 30 Amp Green | Amplifier* |
How to replace the Fuses of the 2024 Dodge Hornet
Replacing the fuses on a 2024 Dodge Hornet involves the following steps:
Materials:
- The new fuse of the correct amperage.
- Fuse puller or needle-nose pliers.
Steps to Replace the Fuses:
- Locate the Fuse Box:
- The 2024 Dodge Hornet has two fuse boxes: one in the engine compartment and one inside the cabin.
- The engine compartment fuse box is typically located near the battery or along the side of the engine bay.
- The interior fuse box is often found under the dashboard on the driver’s side or behind a panel on the side of the dash.
- Access the Fuse Box:
- For the engine compartment fuse box, open the hood and locate the fuse box cover. Unclip or unscrew the cover to access the fuses.
- For the interior fuse box, you may need to remove a panel or cover. This can often be done by hand or with a small screwdriver.
- Identify the Faulty Fuse:
- Refer to the fuse diagram on the fuse box cover to identify the specific fuse you need to check or replace.
- Check the fuse visually. A blown fuse will have a broken or burnt wire inside the fuse.
- Remove the Faulty Fuse:
- Use a fuse puller, which is often provided in the fuse box, or a pair of needle-nose pliers to carefully pull the faulty fuse out of its slot.
- Replace the Fuse:
- Get a new fuse of the same type and rating. The rating is usually marked on the fuse itself and also listed in the fuse box diagram.
- Insert the new fuse into the slot, ensuring it is seated firmly.
- Reassemble:
- After replacing the fuse, replace the fuse box cover and ensure it is secured properly.
- If you accessed the interior fuse box, reattach any panels or covers you removed.
- Test the Circuit:
- Turn on the ignition and check the functionality of the circuit that the fuse is responsible for. Ensure the issue is resolved and the new fuse is working correctly.
Tips:
- Always replace fuses with one of the same amperage to avoid electrical issues.
- Keep spare fuses of various ratings in your vehicle for future emergencies.
- If a fuse blows again shortly after replacement, it may indicate an underlying electrical problem that needs professional attention.
Safety Precautions:
- Always turn off the vehicle and remove the key from the ignition before replacing fuses to prevent any electrical shock or short-circuiting.
- Avoid using metal tools like screwdrivers directly in the fuse box as they can cause a short circuit.
FAQs
Fuses in the 2024 Dodge Hornet are designed to protect the vehicle’s electrical circuits from overloading and short circuits.
The fuse box in the 2024 Dodge Hornet is typically located under the dashboard on the driver’s side and the hood near the battery.
A blown fuse in the 2024 Dodge Hornet can be identified by a broken metal filament inside the fuse or by using a multimeter to check for continuity.
If a fuse blows in your 2024 Dodge Hornet, replace it with a fuse of the same amperage. Ensure the new fuse matches the original fuse in both type and rating.
The fuse diagram of the 2024 Dodge Hornet indicates the location, function, and amperage rating of each fuse in the vehicle.
Useful Links
View Full PDF: 2024 Dodge Hornet Owner’s Manual | Auto User Guide
2024 Dodge Hornet Seats And Seat Belts Guide
2024 Dodge Hornet Seats And Seat Belts Guide