2023 Hyundai Elantra Light Bulbs User Guide

This guide covers 2023 Hyundai Elantra light bulb types, replacement, and maintenance to optimize illumination performance and safety. Expect insightful insights and practical advice.

2023 Hyundai Elantra Specs, Price, Features, Milage (Brochure)

Light Bulbs

Consult an authorized HYUNDAI dealer to replace most vehicle light bulbs. It is difficult to replace vehicle light bulbs because other parts of the vehicle must be removed before you can get to the bulb. This is especially true for removing the headlight assembly to get to the bulb(s).
Removing/installing the headlight assembly can result in damage to the vehicle.

Information
The headlight and tail lamp lenses could appear frosty if the vehicle is washed after driving or the vehicle is driven at night in wet weather. This condition is caused by the temperature difference between the lamp inside and outside and does not indicate a problem with your vehicle. When moisture condenses in the lamp, it will be removed after driving with the headlight on. The removable level may differ depending on lamp size, lamp position, and environmental conditions. However, if moisture is not removed, have the vehicle inspected by an authorized HYUNDAI dealer.

WARNING

•  Prior to replacing a lamp, depress the foot brake, move the shift button into P (Park) apply the parking brake, place the ignition switch to the LOCK/OFF position, and take the key with you when leaving the vehicle to avoid sudden movement of the vehicle and to prevent possible electric shock.
•  Be aware the bulbs may be hot and may burn your fingers.
•  When the bulb is disconnected or the lamp connector is removed while the lamp is operating normally, the fuse box electronics may recognize the lamp as malfunctioning. Therefore, a fault record for the lamp may remain in the Diagnostic Trouble Code (DTC) recorded in the fuse box.

Headlight, Parking Lamp, Daytime Running Light, Turn Signal Lamp and Side Marker

1. Headlight (Low)
2.  Headlight (High)
3. Daytime running lamp (DRL)/Parking lamp
4. Turn signal lamp
5. Side marker

WARNING

•  Handle halogen bulbs with care.  Halogen bulbs contain pressurized gas that will produce flying pieces of glass that could cause injuries if broken.
•  Wear eye protection when changing a bulb. Allow the bulb to cool down before handling it.
•  Always handle them carefully, and avoid scratches and abrasions. If the bulbs are lit, avoid contact with liquids.
• Never touch the glass with bare hands. Residual oil may cause the bulb to overheat and burst when lit.
•  A bulb should be operated only when installed in a headlight.
•  If a bulb becomes damaged or cracked, replace it immediately and carefully dispose of it.

1. Open the hood.
2. Disconnect the negative battery cable.
3.  Remove the headlight bulb cover by turning it counterclockwise.
4. Disconnect the headlight bulb socket-connector.
5. Unsnap the headlight bulb retaining wire by pressing the end and pushing it upward.
6. Remove the bulb from the headlight assembly.
7. install a new 2023 Hyundai Elantra headlight bulb and snap the same as the 2022 Hyundai Elantra headlight bulb retaining wire into position by aligning the wire with the groove on the bulb.
8. Connect the headlight bulb socket-connector.
9. Install the 2023 Hyundai Elantra headlight bulb type cover by turning it clockwise.

Information
The headlight aiming should be adjusted after an accident or after the headlight assembly is reinstalled at an authorized HYUNDAI dealer.

Headlight/Daytime running light (DRL) / Parking lamp (LED type)
If the lamp (LED) does not operate, have the system checked by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps have to be replaced with the unit.
A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

Turn signal lamp (Bulb type)

1. Open the hood.
2. Disconnect the negative battery cable.
3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
4. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
5.  Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
6. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly.
7. Push the socket into the assembly and turn the socket clockwise.

Side marker (Bulb type)

1. Open the hood.
2. Disconnect the negative battery cable.
3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
4. Remove the bulb from the socket by pulling out the bulb.
5. Insert a new bulb.

Side marker (LED type)
If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Side repeater lamp replacement (if equipped)

If the LED lamp (1) does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

Bulb type

1. Remove the lamp assembly from the vehicle by prying the lens and pulling the assembly out.
2. Disconnect the bulb’s electrical connector.
3. Separate the socket and the lens parts by turning the socket counterclockwise until the tabs on the socket align with the slots on the lens part.
4. Remove the bulb by pulling it straight out.
5. Insert a new bulb in the socket.
6. Reassemble the socket and the lens part.
7. Connect the bulb’s electrical connector.
8.  Reinstall the lamp assembly to the body of the vehicle.

Rear combination lamp bulb replacement

1. Stop lamp (LED or bulb)
2. Tail lamp (LED or bulb)
3. Turn signal lamp
4. Reverse lamp
5. Rear side marker (LED or bulb)

Tail/Stop lamp/Turn signal lamp/Side marker (Outer lamp) (Bulb type)

1. Open the trunk lid.
   
2. Remove the service cover by pulling out the service cover.”
   
3. Loosen the assembly retaining nuts.
   
4. Remove the rear combination light assembly from the body of the vehicle.
   
   [A] : Tail/Stop lamp, [B]: Turn signal lamp, [C]: Rear side marker
5. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
6. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
7. Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
8. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

Tail lamp/Stop lamp (Inner lamp) (Bulb type)

1. Open the trunk.
2. Loosen the retaining screw of the trunk lid cover and then remove the cover.
   
3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
4. Remove the bulb by pulling it out.
5. Insert a new bulb by inserting it into the socket.
6. Reinstall the trunk lid cover by pushing in the screw.

Reverse lamp (Inner lamp) (Bulb type)

1. Disconnect the connector and then remove the nuts by turning the nuts counterclockwise.
2. Take the light assembly out.
   
3.  Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly.
4.  Remove the bulb by pulling it out.
5. Insert a new bulb by inserting it into the socket.
6. Install the light assembly to the trunk.
7.  Reinstall the trunk lid cover by pushing in the screw.

Stop/Tail lamp and rear side marker (LED type)
If the LED lamp does not operate, have the vehicle checked by an authorized HYUNDAI dealer.

High-mounted stop lamp replacement

1. Open the trunk.
2. Remove the socket by turning it counterclockwise until the tabs on the socket align with the slots.
3. Remove the bulb from the socket by pressing it in and rotating it counterclockwise until the tabs on the bulb align with the slots in the socket. Pull the bulb out of the socket.
4.  Insert a new bulb by inserting it into the socket and rotating it until it locks into place.
5. Install the socket in the assembly by aligning the tabs on the socket with the slots in the assembly. Push the socket into the assembly and turn the socket clockwise.

License Plate Light Bulb Replacement

1. Using a flat-blade screwdriver gently pry the lens cover from the lamp housing.
2.  Remove the bulb by pulling it straight out.
3. Install a new bulb.
4. Reinstall in the reverse order.

Interior Light Bulb Replacement

1. Using a flat-blade screwdriver, gently pry the lens from the interior lamp housing.
2. Remove the bulb by pulling it straight out.
   WARNING
   Prior to working on the Interior Lights, ensure that the “OFF” button is depressed to avoid burning your fingers or receiving an electric shock.
3. Install a new bulb in the socket.
4. Align the lens tabs with the interior lamp housing notches and snap the lens into place.

NOTICEb
Use care not to dirty or damage lenses, lens tabs, and plastic housings.

If the LED lamp does not operate,
we recommend that the system be inspected by an authorized HYUNDAI dealer.
The LED lamps cannot be replaced as a single unit because it is an integrated unit. The LED lamps have to be replaced with the unit. A skilled technician should check or repair the LED lamp, for it may damage related parts of the vehicle.

FAQ

What types of light bulbs does the Hyundai Elantra 2023 use?
The Elantra 2023 comes with a variety of light bulbs, including halogen bulbs, LED bulbs, and incandescent bulbs.

How long do 2023 Elantra LED bulbs last?
LED bulbs can last up to 25,000 hours or more, which is significantly longer than halogen bulbs.

What are daytime running lights in the 2023 Elantra ?
Daytime running lights (DRLs) are low-intensity lights that are designed to make a vehicle more visible during the day. The Elantra 2023 comes equipped with LED DRLs.

What are the benefits of 2023 Hyundai Elantra LED headlights?
LED headlights offer brighter illumination, a longer lifespan, and are more energy-efficient compared to halogen headlights.

How often should I replace the light bulbs in my Hyundai Elantra 2023?
The lifespan of a light bulb depends on its type and usage. However, it is recommended to replace the bulbs every 2-3 years or when they start to dim.

Useful Link

View Full PDF: 2023 Toyota Camry User Guide | Auto User Guide

2023 Toyota Camry Specs, Price, Features and Mileage (Brochure)

2023 Toyota Camry Before Driving User Guide