Auto User Guide

BYD SEAL Keys and Smart Key User Guide

BYD SEAL-Featured

BYD Logo

BYD SEAL Keys and Smart Key User Guide

The BYD SEAL has a smart key system that enables remote controls, push-button starting, and keyless entry. By allowing drivers to lock, unlock, and start the car without physically using the key, it improves convenience and security.

2023 BYD TANG Review, Price, Features and Mileage (Brochure)

BYD Doors and Keys Guide

Keys
The vehicle is equipped with keys, including the electronic smart key, mechanical key (installed in the electronic smart key) and NFC key card* to enable functions such as unlocking/locking doors and starting the vehicles.

Electronic Smart Key
Lock or unlock all doors by pressing the front door microswitch while carrying the electronic smart key. Buttons on the key help you lock or unlock doors, open the trunk, and start the vehicle remotely.

  1. Lock button
  2. Unlock button
  3. Trunk release button
  4. Start/Stop button
  5. Indicator
  6. Mechanical Key
    BYD SEAL Keys and Smart Key-fig 1

WARNING

  • The button (coin) battery in the smart key is hazardous and both new and used batteries are to be kept away from children at all times.
  • If swallowed or placed inside any part of the body, a lithium button battery can cause severe or fatal injuries in two hours or less.
  • Medical attention should be sought immediately if it is suspected the button battery has been swallowed or placed inside any part of the body.

CAUTION

  • The smart key is an electronic component. Observe the following instructions to prevent damage to the key:
    • Do not place the smart key in a position exposed to high temperature, such as on the dashboard.
    • Do not tamper with the smart key.
    • Do not hit other objects with the smart key or drop it.
    • Do not immerse the key in water or clean it in the ultrasonic scrubber.
    • Do not place smart keys with devices that emit electromagnetic waves, such as the mobile phone.
    • Do not attach to the smart key any objects (such as a metal seal) capable of cutting off electromagnetic wave signals.
    • You can register a spare key for the same vehicle. In this case, contact a BYD authorized dealer or service provider immediately.
  • If the electronic smart key cannot operate the door within the normal distance, or the key indicator light is dim or off:
    • Check for nearby radio stations or airport radio transmitters that interfere with the normal operation of electronic smart keys.
    • The battery of an electronic smart key may be exhausted. Check the battery inside the electronic smart key. It is recommended to contact a BYD authorized dealer or service provider for inspection as soon as possible.
  • If you lose your smart key, it is recommended to contact a BYD authorized dealer or service provider as soon as possible to reduce the risk of vehicle theft or accidents.
  • Do not change the transmission frequency arbitrarily, increase the transmission power (including additional transmission frequency amplifier), or arbitrarily connect the external detection antenna or switch other transmitting detection antennas.
  • Do not cause harmful interference to legitimate radio communication services when used; once there is interference, stop using and mining immediately.
  • The use of micropower radio equipment must be free from interference of all radio services or from radiation of devices for industrial, scientific and medical applications.
  • When leaving the vehicle, always carry your key and lock the vehicle. Never leave anyone (especially children) alone in the vehicle.
  • People implanted with pacemakers or defibrillators should stay away from the detection antennas of intelligent entry and start systems, as electromagnetic waves can affect the normal use of such devices. In addition to people implanted with pacemakers
    or defibrillators, those who use other electronic medical devices should also consult the manufacturer on the use of such devices under the influence of electromagnetic waves. Electromagnetic waves may bring unknown consequences to the use of such medical devices.

Mechanical Key
Use the mechanical key (inside the smart key) to lock or unlock the driver’s door. When the key is not used, be sure to insert the mechanical key back into the smart key.

Taking out the mechanical key
When using the mechanical key in the electronic smart key, slide the lock-up button in the direction of arrow① and push the back cover of the electronic smart key in the direction of arrow②, hook the head hole of the mechanical key with the projection parts at both ends of the back cover of smart key and pull it in the direction of arrow③ to take out the mechanical key, as shown in the figure.BYD SEAL Keys and Smart Key-fig 2

  • After using the mechanical key, insert it in the opposite direction and close the back cover of the smart key.

NFC Card*

  • NFC card* – Place the NFC key card at the mark on the left side mirror to unlock/lock all the doors.

CAUTION

  • NFC card is an electronic product. The following instructions must be observed to prevent function failure of or damage to the card:
    • Do not place the NFC card in the charging area when the wireless charger is on.
    • Do not attach any object (such as a metal seal or metal phone case) that may cut off electromagnetic waves.
    • Do not place the NFC card in a position exposed to high temperature, such as on the dashboard.
    • Do not bend the card with force.
    • Do not place the card with other hard objects.
  • NFC cards use near-field communication technology, requiring a detection distance of less than 2 cm. Hold your NFC card close to the side mirror for 1-2 seconds.
  • The NFC smart card is a key configured for the vehicle based on the near field communication method. In order to ensure vehicle safety, handle it with care. If it is lost, going to a BYD authorized dealer or service provider for blocking of the lost card and re-configuration is recommended.

Locking/Unlocking Doors

Locking/Unlocking with Mechanical Key

  1. Push the left side of a hidden door handle, and turn the right side to get a finger height, holding it by a hand.
    BYD SEAL Keys and Smart Key-fig 3
  2. Once the right side is extended, pull the middle of the handle outward to extend the handle.
    BYD SEAL Keys and Smart Key-fig 4
  3. Insert the mechanical key into the hole and turn the key.
  • Unlock the driver’s side door by turning the key clockwise.
  • Lock the driver’s side door by turning the key counterclockwise.
    BYD SEAL Keys and Smart Key-fig 5

CAUTION

  • After pulling out the mechanical key, pull the driver’s door handle to open the door.

Opening with Interior Door Handle

  • When the vehicle is unlocked, pull the handle once to open the door from inside the vehicle.
    BYD SEAL Keys and Smart Key-fig 6
  • When the vehicle is locked, pull the handle twice to open the door from inside the vehicle.

WARNING

  • Don’t let children play with the pull handle in case the door being accidently opened when driving then cause accidents.
  • When a child is in the vehicle, make sure to enable the child protection lock function.

CAUTION

  • Due to the child protection lock function, the rear doors can only be opened when the child protection lock is unlocked, or it cannot be opened from inside the vehicle.

Locking/Unlocking with Smart Key

  • The wireless remote control is used to unlock or lock all doors at a close distance, and complete additional functions.
  • In the active area, press the associated button on the registered smart key to lock or unlock all doors.

Locking:

  • When all the doors, the hood and the trunk lid are closed, press the lock button to lock all the doors. The hidden door handles fold automatically. If the vehicle is shut down, the side mirrors will fold (when the Auto-Fold is enabled) with turn signals flashing once. If the ignition has not been switched off, the side mirrors will not fold, the turn signals will not flash, and the alarm will sound once. Check whether all doors are securely locked.
    BYD SEAL Keys and Smart Key-fig 7
  • If any door is unlocked, the side mirrors do not fold, the turn signals do not flash, the door handles do not fold and the alarm sounds once.
  • If the hood or trunk is not closed, the side mirrors do not fold*, the turn signals do not flash, and the alarm sounds once.

Unlocking:

  • Press the unlock button. All doors are unlocked, the hidden door handles* automatically extend, and the turn signal flashes twice.
  • Unlocking all doors with the smart key may turn on interior lights
    and keep them on for 15 seconds then go out (when the interior light “DOOR” switched is turned on on the infotainment touchscreen), even if no door is opened.
  • If the anti-theft alarm system is armed, open any door within 30 seconds after unlocking with the smart key, or all doors will relock automatically and the four door handles retract*.

Finding the Vehicle

  • When the vehicle is in anti-theft mode, press the lock button. The vehicle sounds a long beep and turn signals flashes 15 times. Use this function to locate the vehicle when it cannot be found.
  • When the vehicle is in car search mode, press the lock button again. The vehicle enters the next car search mode.

Raising/Lowering Windows with Smart Key*

  • When the ignition is switched off:
    • Press and hold the lock button on the smart key to raise the four windows.
    • Press and hold the unlock button on the smart key to lower the four windows.

To enable or disable key unlock/lock/closing window functions, go to Infotainment touchscreen Vehicle→ settings → Window and Lock.

CAUTION

  • Before activating the remote window closing, please confirm that any body part of passengers in the vehicle will not be stuck or clamped by the window.

Locking/Unlocking with Microswitch Locking

  • With the doors closed but not locked, press the microswitch on the front door handle while carrying the smart key, then all doors lock at the same time. The hidden door handles fold automatically. If the vehicle is shut down, the side mirrors will fold (when the Auto-Fold is enabled) with turn signals flashing once. If the ignition has not been switched off, the side mirrors will not fold, the turn signals will not flash, and the alarm will sound once.
    BYD SEAL Keys and Smart Key-fig 8
  • If any door is not closed, the side mirrors do not fold, the turn signals do not flash, the door handles do not fold and the alarm sounds once.
  • If the hood or trunk is not closed, the side mirrors do not fold*, the turn signals do not flash, and the alarm sounds once.

Unlocking

  • When the vehicle is locked, press the microswitch on the front door handle while carrying the smart key. All doors unlock at the same time. The hidden door handle extends automatically and the turn signal flashes twice.
  • If the anti-theft alarm system is armed, open a door within 30 seconds after the unlocking. or all doors will relock automatically and the four door handles retract*.
  • Pressing the microswitch does not work if:
    • This is performed while a door is being opened or closed.
    • The key is left in the vehicle.

REMINDER

  • If the electronic smart key is too close to an exterior door handle or window, it may not be possible to activate the entry function.

Raising/Lowering Windows with Microswitch

  • When the ignition is switched off, press and hold the microswitch while carrying the smart key to roll up or down all windows (By default, lifting the window function is activated and lowering the window function is closed).
  • To enable or disable microswitch lifting/lowering window function, go to infotainment touchscreen → → Vehicle Settings → Window and Lock.

Locking/Unlocking the Trunk Opening the trunk with smart key
Double-press the trunk release button on the smart key. The turn signals then flash twice.

  • Anti-forget key
    • If the key is placed in the vehicle or in the trunk with the vehicle locked, when you close the trunk, the vehicle automatically unlocks and the turn signals flash twice.
      BYD SEAL Keys and Smart Key-fig 9

Unlocking the trunk with microswitch

  • With the vehicle locked, press the rear microswitch while carrying a valid key to unlock the trunk.
  • With the vehicle unlocked, press the rear microswitch to open the trunk.
    BYD SEAL Keys and Smart Key-fig 10

Opening the trunk from inside
With the vehicle unlocked, pull up the electrical trunk lid button to open the lid.

  • If the vehicle speed is greater than 3 km/h, the trunk lid cannot be opened by pulling up the button.
    BYD SEAL Keys and Smart Key-fig 11

Trunk lid close button

  • When the trunk lid is open and stationary, press the trunk close button to close this lid.
  • Press this button a second time to stop the lid at the current position. Press this button again to have the lid move in the opposite direction.
    BYD SEAL Keys and Smart Key-fig 12

Vehicle lock button*

  • When the ignition is off, pressing the lock switch while carrying a valid smart key closes the trunk, locks the entire vehicle, and arms the anti-theft alarm system.

REMINDER

  • Before closing the trunk, verify that the doors, windows, sunroof, etc. are closed to avoid property loss.

Emergency trunk releasing from inside

  1. Pull up the folding release clasp on the seatback to fold the rear seatback.
    BYD SEAL Keys and Smart Key-fig 13
  2. There is an emergency unlocking mechanism on the lid cover, open the lid cover in the car by pulling the emergency opening lever on the left (as shown in the figure).
    BYD SEAL Keys and Smart Key-fig 14

REMINDER

  • When the entire vehicle is powered off, the trunk can be unlocked from inside the vehicle.

Setting trunk opening height*

  • Open the trunk manually or automatically to the desired position, keep it at this position, and then press and hold the interior trunk button for over three seconds. The speaker sounds for one second, indicating that the opening height is set to the current position.
  • Set the trunk opening height by going to the infotainment touchscreen → → Vehicle Settings → Window and Lock.

Anti-pinch function
If the trunk receives a hindering force while it is closing, it will automatically switch to the opposite direction. If it receives a hindering force while it is opening, it will halt.

When the trunk fails to act automatically
Close the trunk manually for recovery.

When reconnecting the low-voltage battery
Close the trunk manually to ensure the power trunk lid functions normally.

WARNING

  • In order to prevent serious injury or death, make sure to observe the following precautions when you operate the trunk lid:
    • Never activate the anti-pinch function with your body.
    • If there are people nearby, inform them that the lid is about to open or close for safety.
    • Make sure hands and fingers are clear from the lid area when closing it.
    • When opening or closing the trunk, make sure the surrounding area is safe.
    • Make sure the trunk is closed when driving.
    • Remove any load like ice or snow from the lid before opening the trunk, otherwise the lid may close again.
    • Do not move the lid when it is opening or closing automatically.
    • Be mindful of windy weather when opening or closing the trunk.
    • The anti-pinch function may fail to work if an object is caught right before the trunk is fully closed.
    • The lid may start closing before fully opened. Be mindful of the possibility of the lid to open or close automatically when the vehicle is on the slope. Before loading or unloading the trunk, make sure the lid is fully open and secure.
    • The anti-pinch function may fail depending on the object shape. Be specially careful not to get your finger or any other object caught.

Locking/Unlocking with NFC Card* Locking doors
When doors are closed but unlocked, hold the NFC key close to the designated area on the driver’s side mirror. All doors can then be locked at the same time. The turn signals flash once when the vehicle is powered off.BYD SEAL Keys and Smart Key-fig 15

Unlocking doors
When doors are locked, hold the NFC key close to the designated area on the driver’s side mirror. Then all doors can be unlocked at the same time. The turn signals flash twice.

  • Doors will not be locked/unlocked when the NFC keys are close to the designated area on the driver’s side mirror when:
    • The NFC key is placed close to the designated area on the driver’s side mirror while doors are being opened or closed.

WARNING

  • The key-less start permission lasts for up to four minutes.

REMINDER

  • After unlocking the vehicle in anti-theft mode with the NFC key, open any door within 30 seconds. or all doors will relock automatically.
  • After unlocking by NFC key, the user can start the vehicle without the key in a stipulated period, while this will be disabled after valid locking.

Locking/Unlocking with Central Locking Locking or unlocking the vehicle with the central locking
See “Driver’s Door Switches” in this chapter.

Locking or unlocking doors automatically

  • All doors automatically lock at vehicle speeds above 8 km/h.
  • Press the START/STOP button to switch the ignition off. Then, all doors are unlocked automatically.

Locking and unlocking all doors concurrently

  • When the vehicle is not in anti-theft mode, the backlight of the central locking button turns on if the vehicle is locked and turns off if the vehicle is unlocked.
  • Pressing the central lock button locks all doors so that any attempt to open any door from the outside fails. At this time, pull the interior handle to unlock a door and pull a second time to open it.

REMINDER

  • All doors unlock automatically when the vehicle suffers a strong impact, depending on the impact intensity and accident type.

Emergency Locking with Mechanical Key

  • When the central locking fails, lock the driver’s door with the mechanical key. Use the key to turn the emergency locking knobs of the other three doors counterclockwise to the locked state, and then close the doors. At this time, the entire vehicle has been locked so that doors cannot be opened with any of the exterior door handles.
  • To unlock the doors, unlock the driver’s door with the mechanical key first, then enter the vehicle and pull other interior door handles twice to open the doors.
    BYD SEAL Keys and Smart Key-fig 16

REMINDER

  • Prevent excessive force from distorting or breaking the key during the operation.

2023 BYD TANG Review, Price, Features and Mileage (Brochure)

Smart Access and Start System

Use the smart key to unlock or lock the vehicle doors and start the vehicle.

Access
Use the smart key to unlock or lock the vehicle doors.

REMINDER

  • If the electronic smart key is too close to a door handle or window, it may not be possible to activate the entry function.

Start-up
With the smart key inside, press the brake pedal and the START/STOP button to start the vehicle.

CAUTION

  • Do not touch the power button while driving.

Antenna Positions

  1. Interior detection antenna
  2. Exterior detection antenna
    BYD SEAL Keys and Smart Key-fig 17

Active Area
The smart access and start functions take effect only when the registered smart key is within the active area.

  1. Active area of the access function: about 1 meter from the front door handle and the exterior trunk switch.
  2. Active area of the start function: inside the cabin.

If another smart key is near this vehicle’s smart key, unlocking may take longer than usual, which is normal.BYD SEAL Keys and Smart Key-fig 18

REMINDER
In the following situation, smart access and start system may not work normally:

  • There is a strong electromagnetic field nearby, such as TV towers, power stations, and broadcasting stations.
  • The smart key is being carried along with a communication device, such as a two-way radio or mobile phone.
  • The smart key is in contact with or covered by any metal object.
  • The door handle is operated too quickly.
  • Another wireless remote control function is being used nearby.
  • When the smart key battery runs out.
  • The smart key is close to high-voltage equipment or equipment that produces noise.
  • The smart key is being carried along with another smart key or radio-wave-emitting device.
  • Even within the active area, the smart key may not work properly in certain locations, for example, on the dashboard, in the glove box, or on the floor.
  • If the smart access system is not working properly and it is impossible to enter the vehicle, the mechanical key can be used to lock/unlock the driver’s door, or the wireless remote control function can be used to lock/unlock all doors.
  • Pressing the START/STOP button may not enable the start function due to:
  • Smart key failure. If the smart key warning light on the instrument cluster lights up, and the instrument cluster displays the message “Smart key power is low. Please replace the battery as soon as possible”, the battery of the key may be exhausted.
  • If the smart access and start system cannot work properly due to system failures, bring all smart keys to a BYD authorized dealer or service provider for repair.

Saving battery power

  • The smart key communicates with the vehicle even when the vehicle is not running. Therefore, do not leave the smart key in the vehicle or within two meters from the vehicle.
  • Receiving strong electromagnetic waves for a long time drains the battery of the smart key quickly. The smart key must be kept at least one meter away from the following devices:
    • TVs
    • PCs
    • Wireless telephone chargers
    • Electroliers
    • Fluorescent desk lamps

Child Protection Lock

Configuration I
Child protection locks are designed to prevent children in rear seats from accidentally opening rear doors. Such locks are provided on the sides of the left and right rear doors.

  1. Deactivating the child protection lock
  2. Activating the child protection lock
    BYD SEAL Keys and Smart Key-fig 19

Activating the child protection lock

  • Move the latch in the direction of arrow② to turn on the child protection lock. The door cannot be opened from inside. Use the exterior door handle to open this door.

Deactivating the child protection lock

  • Move the latch in the direction of arrow① to turn off the child protection lock. The door can be opened from inside.

Configuration II
Child protection locks on the driver door switches are designed to prevent children sitting in the rear seats from inadvertently opening the rear doors.

  1. Child protection lock for the rear left door
  2. Child protection lock for the rear right door
    BYD SEAL Keys and Smart Key-fig 20

To activate child protection locks, press the child protection lock button① or②. The corresponding indicator lights up. At this time, the occupants cannot open the rear door on the corresponding side. To unlock the door, press the child protection lock button for the corresponding side again or use the exterior door handle.

WARNING

  • Before driving, especially when a child is in the vehicle, ensure that the doors are closed and the child protection lock function is enabled.
  • Proper use of seat belts and activation of child protection lock helps prevent the driver and passengers from being thrown out of the vehicle in an accident, and also prevents a door from being opened accidentally.
  • After the child protection lock is locked, doors cannot be opened from inside the car, and the window switch for the corresponding rear door cannot be used to raise or lower the window.

2023 BYD TANG Review, Price, Features and Mileage (Brochure)

BYD SEAL Infotainment System User Guide

BYD SEAL Seats and Seat Belt User Guide

Scroll to Top