2025 Toyota Tacoma Four-Wheel Drive User Guide
The 2025 Toyota Tacoma Four-Wheel Drive will be covered in this guide, along with its improved features, performance advantages, and cutting-edge off-road capabilities. This thorough evaluation covers all you need to know, whether you’re looking for a dependable 4×4 car or are an adventurer.
2024 Toyota Tacoma Specs, Price, Features, Mileage and Review
Toyota Four-wheel drive System Guide
Use the front-wheel drive control switch to select the following transfer modes:
Front-wheel drive control switch
- “2H” (high speed position, two-wheel drive)
Use this for normal driving on dry hard-surfaced roads. This position gives greater economy, quietest ride and least wear. Hold down and turn the dial to select. - “4H” (high speed position, four-wheel drive)
Use this for driving only on tracks that permit the tires slide, like off-road, icy or snow-covered roads. This position provides greater trac-tion than two-wheel drive. The “4HI” indicator will come on.
- Hold down and turn the dial to select. “4L” (low speed position, four-wheel drive) Use this for maximum power and traction. Use “4L” for climbing or descending steep hills, off-road driving, and hard pulling in sand, mud or deep snow. The “4LO” indicator will come on. Hold down and turn the dial to select.
Shifting between “2H” and “4H”
Shifting from “2H” to “4H”
- Reduce vehicle speed to less than 62 mph (100 km/h).
- Push and turn the front-wheel drive control switch to “4H”. The “4HI” indicator will come on.
Shifting from “4H” to “2H”
- Reduce vehicle speed to less than 62 mph (100 km/h).
- Push and turn the front-wheel drive control switch to “2H”. The “4HI” indicator will go off.
Shifting between “4H” and “4L”
Shifting from “4H” to “4L”
Vehicles with an Automatic transmission
- Stop the vehicle completely and continue to depress the brake pedal.
- Shift the shift lever to N.
- Push and turn the front-wheel drive control switch to “4L”. The “4LO” indicator will come on and the “4HI” indicator go off.
Vehicles with a Manual transmission
- Stop the vehicle completely and continue to depress the brake pedal.
- Depress and hold the clutch pedal.
- Push and turn the front-wheel drive control switch to “4L”. The “4LO” indicator will come on and the “4HI” indicator go off.
Shifting from “4L” to “4H”
Vehicles with an Automatic transmission
- Stop the vehicle completely and continue to depress the brake pedal.
- Shift the shift lever to N.
- Push and turn the front-wheel drive control switch to “4H”. The “4LO” indicator will go off and the “4HI” indicator come on.
Vehicles with a Manual transmission
- Stop the vehicle completely and continue to depress the brake pedal.
- Depress and hold the clutch pedal.
- Push and turn the front-wheel drive control switch to “4H”. The “4LO” indicator will go off and the “4HI” indicator come on.
When the front-wheel drive control switch is shifted to “4L”
VSC is automatically turned off.
If the “4HI” indicator flashes
The transfer mode may not successfully change. Drive straight ahead while accelerating or decelerating, or drive in reverse.
If the “4HI” indicator is ON and the “4LO” indicator continues to flash
Shift the shift lever to D or R (Vehicles with an Automatic transmission) or 1st gear or Reverse (Vehicles with a Manual transmission) and drive the vehicle slowly, then stop.
If the “4HI” indicator continues to flash and the “4LO” indicator is ON
Shift the shift lever to D or R (Vehicles with an Automatic transmission) or 1st gear or Reverse (Vehicles with a Manual transmission) and drive the vehicle slowly, then stop.
If the “4HI” indicator is ON and the “4LO” indicator continues to flash and a buzzer sounds
The shift lever is not in N (Vehicles with an Automatic transmission) or the clutch pedal is not held in the depressed position (Vehicles with a Manual transmission) and/or the vehicle is moving. Stop the vehicle completely, shift the shift lever to N and make sure that the indicator stops flashing.
If the “4HI” indicator continues to flash and the “4LO” indicator is ON and a buzzer sounds The shift lever is not in N and/or the vehicle is moving. Stop the vehicle completely, shift the shift lever to N (Vehicles with an Automatic trans-mission) or the clutch pedal is not held in the depressed position (Vehicles with a Manual transmis-sion) and make sure that the indica-tor stops flashing
If the “4HI” and “4LO” indicator flashes rapidly
There may be a malfunction in the four-wheel drive system. Have the vehicle inspected by your Toyota dealer immediately.
Shift between 4H and 4L at low temperature
Immediately after starting the engine in a low-temperature envi-ronment, the shift between 4H and 4L may be prohibited because the transmission fluid is cold. At that time, a warning message will be dis-played in the multi-information dis-play, so follow the message and operate the front-wheel drive control switch again after warming up.
2024 Toyota Tacoma Specs, Price, Features, Mileage and Review
Four-wheel drive usage fre-quency
You should drive in four-wheel drive for at least 10 miles (16 km) each month. This will assure that the front drive components are lubricated.
WARNING
Shifting the front-wheel drive control switch from “2H” to “4H” while driving
Never operate the front-wheel drive control switch if the wheels are slipping. Stop the slipping or spinning before shifting.
When the vehicle is parked (Vehicles with an Automatic transmission)
If the shift lever is moved before the “4HI” or “4LO” indicator turns on/off, the transfer mode may not be shifted completely. The trans-fer mode disengages both the front and rear driveshafts from the powertrain and allows the vehicle to move regardless of the shift position. (At this time, the indica-tor blinks and the buzzer sounds.) Therefore, the vehicle is free to roll even if the automatic trans-mission is in P. You or someone else could be seriously injured. You must complete the shifting of the transfer mode before placing transmission in P.
Useful Links:
2024 Toyota Tacoma Specs, Price, Features, Mileage and Review