2024 Jeep Wagoneer Warning and Indicator Lights Owner’s Manual
Explore the 2024 Jeep Wagoneer warning and indicator lights for vehicle status updates. Understanding these indicators helps you spot problems early, making driving safer, smoother, and more dependable.
2023 – 2024 Jeep Wagoneer Review, Price, Features And Mileage (Brochure)
Video: 2024 Jeep Wagoneer Dashboard Warning Indicators
Jeep WARNING LIGHTS AND MESSAGES Guide
The warning/indicator lights will illuminate the instrument panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner’s Manual, which you are advised to read carefully in all cases. Always refer to the information in this chapter in the event of a failure indication. All active telltales will display first if applicable. The system check menu may appear differently based on equipment options and current vehicle status. Some telltales are optional and may not appear.
RED WARNING LIGHTS
Air Bag Warning Light
This warning light will illuminate to indicate a fault with the airbag and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN position. This light will illuminate with a single chime when a fault with the airbag has been detected, it will stay on until the fault is cleared. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.
Brake Warning Light
If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop.
The dual brake system provides a reserve braking capacity in the event of a failure of a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level.
The light will remain on until the cause is corrected.
NOTE:
The light may flash momentarily during sharp cornering manoeuvres, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked.
If brake failure is indicated, immediate repair is necessary.
WARNING!
Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately.
Vehicles equipped with the Anti-Lock Brake System
(ABS) are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS is required.
Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approxi-mately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer.
The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position.
NOTE:
This light shows only that the parking brake is applied. It does not show the degree of brake application.
Battery Charge Warning Light
This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible. This indicates a possible problem with the electrical system or a related component.
Door Open Warning Light
This indicator will illuminate when a door is ajar/open and not fully closed.
NOTE:
If the vehicle is moving, there will also be a single chime.
Drowsy Driver Detected Warning Light — If Equipped
Electric Power Steering (EPS) Fault Warning Light
This warning light will turn on when there’s a fault with the EPS system.
WARNING!
Continued operation with reduced assistance could pose a safety risk to yourself and others. Service should be obtained as soon as possible.
Electronic Throttle Control (ETC) Warning Light
This warning light will illuminate to indicate a problem with the ETC system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible.
NOTE:
This light may turn on if the accelerator and brake pedals are pressed at the same time.
If the light continues to flash when the vehicle is running, immediate service is required and you may experience reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing. The light will come on when the ignition is placed in the ON/RUN position and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer.
Engine Coolant Temperature Warning Light
If the light turns on while driving, safely pull over and stop the vehicle. If the Air Conditioning (A/C) system is on, turn it off. Also, shift the transmission into NEUTRAL (N) and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.
Hood Open Warning Light
This warning light will illuminate when the hood is left open and not fully closed.
NOTE:
If the vehicle is moving, there will also be a single chime.
Liftgate Open Warning Light
This warning light will illuminate when the liftgate is open.
NOTE:
If the vehicle is moving, there will also be a single chime.
Night Vision Animal Detected Warning Light — If Equipped
If enabled, a chime will sound and a video pop-up may display when a detection occurs.
Night Vision Pedestrian Detected Warning Light — If Equipped
The Night Vision Pedestrian Warning Light will illuminate in red when a pedestrian is detected directly in the vehicle’s path, near the headlights, and a collision is possible.
If enabled, a chime will sound and a video pop-up may display when a detection occurs.
Oil Pressure Warning Light
This warning light will illuminate to indicate low engine oil pressure. If the light turns on while driving, stop the vehicle, shut off the engine as soon as possible, and contact an authorized dealer. A chime will sound when this light turns on.
Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine.
Oil Temperature Warning Light
Seat Belt Reminder Warning Light
This warning light indicates when the driver or passenger seat belt is unbuckled. When the ignition is first placed in the ON/RUN position and if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound
Transmission Temperature Warning Light — If Equipped
This warning light will illuminate to warn of a high transmission fluid temperature. This may occur with strenuous usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off. Once the light turns off, you may continue to drive normally.
WARNING!
If you continue operating the vehicle when the Trans-mission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire.
CAUTION!
Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.
Vehicle Security Warning Light —If Equipped
YELLOW WARNING LIGHTS
Anti-lock brake System (ABS) Warning Light
This warning light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN position and may stay on for as long as four seconds.
If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on.
If the ABS light does not turn on when the ignition is placed in the ON/RUN position, have the brake system inspected by an authorized dealer.
Air Suspension Fault Warning Light
This light will illuminate when there is a fault detected in the air suspension system.
Drowsy Driver Detected System Fault Warning Light — If Equipped
Electric Park Brake Warning Light
This warning light will illuminate to indicate the Electric Park Brake is not functioning properly and service is required. Contact an authorized dealer.
Electronic Stability Control (ESC) Active Warning Light
This warning light will indicate when the ESC system is Active. The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN position, and when ESC is activated. It should go out with the engine running. If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometres) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the problem diagnosed and corrected.
- The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN position.
- The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive.
- This light will come on when the vehicle is in an ESC event.
Electronic Stability Control (ESC) OFF Warning Light
Service Active Lane Management Warning Light — If Equipped
This warning light will illuminate when the Active Lane Management system is not operating and requires service. Please see an authorized dealer.
Active Lane Management Warning Light — If Equipped
The Active Lane Management Warning Light will be solid yellow when the vehicle is approaching a lane marker. The warning light will flash when the vehicle is crossing the lane marker.
Low Fuel Warning Light
Fuel Cutoff Failure Warning Light —If Equipped
This light will illuminate if there is a fuel cut-off failure. If this light illuminates, take it to an authorized dealer and have them inspect it.
Low Washer Fluid Warning Light
This warning light will illuminate when the windshield washer fluid is low
Engine Check/Malfunction Indicator Warning Light (MIL)
Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after the engine starts. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing.
When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.
WARNING!
A malfunctioning catalytic converter, as referenced previously, can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.
CAUTION!
Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system. It also could affect fuel economy and drive-ability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.
Night Vision Animal Detected Warning Light — If Equipped
This light alerts the driver that the Night Vision Warning System has detected an animal approaching the vehicle’s path.
Night Vision Pedestrian Detected Warning Light — If Equipped
This indicator light alerts the driver that the Night Vision System has detected a pedestrian approaching the vehicle’s path.
Oil Level Sensor Fault Warning Light —If Equipped
Service 4WD Warning Light —If Equipped
This warning light will illuminate to signal a fault with the 4WD system. If the light stays on or comes on during driving, it means that the 4WD system is not functioning properly and that service is required. We recommend you drive to the nearest service centre and have the vehicle serviced immediately.
Service Adaptive Cruise Control (ACC) Warning Light
This light will turn on when the ACC is not operating and needs service This light will turn on when the ACC system is not operating and needs service.
Service Forward Collision Warning (FCW) Or Pedestrian Emergency Braking (PEB) Warning Light
Service Stop/Start System Warning Light
This warning light will illuminate when the Stop/Start system is not functioning properly and service is required. Contact an authorized dealer for service.
Tire Pressure Monitoring System (TPMS) Warning Light
The warning light switches on and a mes-sage is displayed to indicate that the tyre pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tyre duration and fuel consumption may not be guaranteed.
Should one or more tyres be in the condition mentioned previously, the display will show the indications corre-sponding to each tyre.
CAUTION!
Do not continue driving with one or more flat tyres as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. If a tyre puncture occurs, repair immediately using the dedicated tyre repair kit and contact an authorized dealer as soon as possible.
Each tyre, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tyre inflation pressure label. If your vehicle has tyres of a different size than the size indicated on the vehicle placard or tyre inflation pressure label, you should determine the proper tyre inflation pressure for those tyres.
As an added safety feature, your vehicle has been equipped with a TPMS that illuminates a low tyre pressure telltale when one or more of your tyres is significantly underinflated. Accordingly, when the low tyre pressure tell-tale illuminates, you should stop and check your tyres as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tyre causes the tyre to overheat and can lead to tyre failure. Underinflation also reduces fuel efficiency and tyre tread life and may affect the vehicle’s handling and stopping ability.
Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the driver’s responsibility to maintain correct tyre pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tyre pressure telltale.
Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tyre pressure telltale. When the system detects a malfunction, the telltale will flash for approxi-mately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunction exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tyre pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternative tyres or wheels on the vehicle that prevents the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tyres or wheels on your vehicle to ensure that the replacement or alternate tyres and wheels allow the TPMS to continue to function properly.
CAUTION!
The TPMS has been optimized for the original equipment tyres and wheels. TPMS pressures and warnings have been established for the tyre size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equipment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is recommended that you take your vehicle to an authorized dealer to have your sensor function checked.
Towing Hook Breakdown Warning Light — If Equipped
YELLOW INDICATOR LIGHTS
4WD Low Indicator Light — If Equipped
This light alerts the driver that the vehicle is in the 4WD Low mode. The front and rear driveshafts are mechanically locked together forcing the front and rear wheels to rotate at the same speed. The low range provides a greater gear reduction ratio to provide increased torque at the wheels.
Air Suspension Active Indicator Light — If Equipped
This light will illuminate when the air suspension system is actively adjusting the ride height.
Air Suspension Aerodynamic Height Indicator Light— If Equipped
Air Suspension Entry/Exit Indicator Light— If Equipped
This light will illuminate when the vehicle is manually or automatically lowered from the ride height position downward for easy entry and exit of the vehicle page 125.
Air Suspension Off-Road 1 Indicator Light — If Equipped
This light will illuminate when the air suspension system is set to the Off-Road 1 setting
Air Suspension Off-Road 2 Indicator Light — If Equipped
Auto HOLD! Fault Indicator Light —If Equipped
The Auto HOLD! Fault Indicator light will illuminate If a fault is detected, it will be indicated by a yellow ‘HOLD!’ indicator light that will stay on as long as the fault condition exists.
Forward Collision Warning (FCW) Or Pedestrian Emergency Braking (PEB) Indicator Light
This indicator light illuminates to indicate that FCW or PEB is off page 237.
Maximum Payload Exceeded Indicator Light
NEUTRAL Indicator Light — If Equipped
This light alerts the driver that the 4WD power transfer case is in the NEUTRAL mode and the front and rear driveshafts are disengaged from the powertrain.
TOW/HAUL Indicator Light
This indicator light will illuminate when TOW/HAUL mode is selected.
GREEN INDICATOR LIGHTS
Adaptive Cruise Control (ACC) Set With Target Indicator Light — If Equipped
Adaptive Cruise Control (ACC) Set With No Target Detected Indicator Light —If Equipped
This will display when the ACC is set and the vehicle in front is not detected
Auto HOLD Indicator Light — If Equipped
Auto HOLD keeps your vehicle at a complete stop without you having to keep your foot on the brake pedal. Once engaged a green
The “HOLD” indicator will appear in the Instrument Cluster Display.
Cruise Control SET Indicator Light —If Equipped
Front Fog Indicator Light
This indicator light will illuminate when the front fog lights are on page 55.
Active Lane Management Indicator Light— If Equipped
The Active Lane Management indicator light illuminates solid green when both lane markings have been detected and the system is “armed” and ready to provide visual and torque warnings if an unintentional lane departure occurs page 157.
2023 – 2024 Jeep Wagoneer Review, Price, Features And Mileage (Brochure)
Night Vision Active Indicator Light —If Equipped
Parking/Headlights On Indicator Light
This indicator light will illuminate when the parking lights or headlights are turned on
Sport Mode Indicator Light
This light will turn on when Sport mode is active.
Stop/Start Active Indicator Light
Turn Signal Indicator Lights
When the left or right turn signal is activated, the turn signal indicator will flash independently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right).
NOTE:
- A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.
- Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.
WHITE INDICATOR LIGHTS
Adaptive Cruise Control (ACC) Ready Indicator Light — If Equipped
This light will turn on when ACC has been turned on but is not set on page 131.
Cruise Control Ready Indicator Light
Hill Descent Control (HDC) Indicator Light — If Equipped
This indicator shows when the HDC feature is turned on. The light will be on solid when HDC is armed. HDC can only be armed when the transfer case is in the 4WD Low position and the vehicle speed is less than 30 mph (48 km/h). If these conditions are not met while attempting to use the HDC feature, the HDC indicator light will flash on/off.
Active Lane Management Indicator Light— If Equipped
When the Active Lane Management system is ON, but not armed, the Active Lane Management indicator light illuminates solid white. This occurs when only the left, right, or neither lane line has been detected. If a single lane line is detected, the system is ready to provide only visual warnings if an unintentional lane departure occurs on the detected lane line page 157.
Rear Seat Unoccupied Indicator Light —If Equipped
Select-Speed Control Indicator Light —If Equipped
This light will turn on when Selec-Speed Con-trol is activated.
To activate Selec-Speed Control, ensure the vehicle is 4WD Low and push the button on the Instrument Panel.
NOTE:
If the vehicle is not in 4WD Low, “To Enter Selec-Speed Shift to 4WD Low” will appear in the instrument cluster display.
BLUE INDICATOR LIGHTS
High Beam Indicator Light
This indicator light will illuminate to indicate that the high-beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on,
“flash to pass” scenario.
GRAY INDICATOR LIGHTS
Night Vision Suppressed Indicator Light — If Equipped
Useful Links
2024 Jeep Wagoneer Alarm System Guide
2024 Jeep Wagoneer Instrument Cluster Guide