2022 Toyota Avalon Driving Assist system User Guide

Table of Contents

2022 Toyota Avalon Driving Assist system User Guide

The 2022 Toyota Avalon’s driving assist sensors’ role is explained in this guide. Real-time data from these sensors supports adaptive cruise control, lane departure warning, and collision avoidance.

2023 Toyota Camry Specs, Price, Features and Mileage (Brochure)

Toyota Safety Sense 2.5+

The Toyota Safety Sense 2.5+ consists of the following drive assist systems and contributes to a safe and comfortable driving experience:

Driving assist system

PCS (Pre-Collision System)
LTA (Lane Tracing Assist)
AHB (Automatic High Beam)
RSA (Road Sign Assist) (if equipped)
Dynamic radar cruise control with full-speed range

WARNING

Toyota Safety Sense 2.5+

The Toyota Safety Sense 2.5+ is designed to operate under the assumption that the driver will drive safely, and is designed to help reduce the impact to the occupants and the vehicle in the case of a collision or assist the driver in normal driving conditions. As there is a limit to the degree of recognition accuracy and control performance that this system can provide, do not overly rely on this system. The driver is always responsible for paying attention to the vehicle’s surroundings and driving safely.

Sensors

Radar sensor
Front camera

WARNING

To avoid malfunction of the radar sensor

Observe the following precautions.
Otherwise, the radar sensor may not operate properly, possibly leading to an accident resulting in death or serious injury.
Keep the radar sensor and the radar sensor cover clean at all times.
Radar sensor
Radar sensor cover
If the front of the radar sensor or the front or back of the radar sensor cover is dirty or covered with water droplets, snow, etc., clean it.
Clean the radar sensor and radar sensor cover with a soft cloth to avoid damaging them.
Do not attach accessories, stickers (including transparent stickers) or other items to the radar sensor, radar sensor cover or surrounding area.
Do not subject the radar sensor or its surrounding area to a strong impact.
If the radar sensor, front grille, or front bumper has been subjected to a strong impact, have the vehicle inspected by your Toyota dealer.
Do not disassemble the radar sensor.
Do not modify or paint the radar sensor or radar sensor cover.
In the following cases, the radar sensor must be recalibrated. Contact your
Toyota dealer for details.
When the radar sensor or front grille are removed and installed, or replaced
When the front bumper is replaced

WARNING

To avoid malfunction of the front camera Observe the following precautions. Otherwise, the front camera may not operate properly, possibly leading to an accident resulting in death or serious injury.
Keep the windshield clean at all times.
If the windshield is dirty or covered with an oily film, water droplets, snow, etc., clean the windshield.
If a glass coating agent is applied to the windshield, it will still be necessary to use the windshield wipers to remove water droplets, etc. from the area of the windshield in front of the front camera.
If the inner side of the windshield where the front camera is installed is dirty, contact your Toyota dealer. Do not attach objects, such as stickers, transparent stickers, etc., to the outer side of the windshield in front of the front camera (shaded area in the illustration).
A: From the top of the windshield to approximately 0.4 in. (1 cm) below the bottom of the front camera
B: Approximately 7.9 in. (20 cm) (Approximately 4.0 in. [10 cm] to the right
and left from the center of the front camera) If the part of the windshield in front of the front camera is fogged up or covered with condensation or ice, use the windshield defogger to remove the fog, condensation or ice.
If water droplets cannot be properly removed from the area of the windshield in front of the front camera by the windshield wipers, replace the wiper insert or wiper blade.
Do not attach window tint to the windshield.
Replace the windshield if it is damaged or cracked. After replacing the windshield, the front camera must be recalibrated. Contact your Toyota dealer for details.
Do not allow liquids to contact the front camera.
Do not allow bright lights to shine into the front camera.
Do not dirty or damage the front camera. When cleaning the inside of the windshield, do not allow glass cleaner to contact the lens of the front camera. Also, do not touch the lens. If the lens is dirty or damaged, contact your Toyota dealer.

WARNING

Do not subject the front camera to a strong impact.
Do not change the installation position or direction of the front camera or remove it.
Do not disassemble the front camera.
Do not modify any components of the vehicle around the front camera (inside rearview mirror, etc.) or ceiling.
Do not attach any accessories to the hood, front grille or front bumper that may obstruct the front camera. Contact your Toyota dealer for details.
If a surfboard or other long object is to be mounted on the roof, make sure that it will not obstruct the front camera.
Do not modify the headlights or other lights.

If a warning message is displayed on the multi-information display

A system may be temporarily unavailable or there may be a malfunction in the system. In the following situations, perform the actions specified in the table. When the normal operating conditions are detected, the message will disappear and the system will become operational. If the message does not disappear, contact your Toyota dealer.

Situation	Action
When the area around a camera is covered with dirt, moisture (fogged up, covered with condensation, ice, etc.), or other foreign matter	Using the wiper and A/C function, remove the dirt and other attached matter.
When the temperature around the front camera is outside of the opera- tional range, such as when the vehi- cle is in the sun or in an extremely cold environment	If the front camera is hot, such as after the vehicle had been parked in the sun, use the air conditioning sys- tem to decrease the temperature around the front camera. If a sunshade was used when the vehicle was parked, depending on its type, the sunlight reflected from the surface of the sunshade may cause the temperature of the front camera to become excessively high.
	If the front camera is cold, such after the vehicle is parked in an extremely cold environment, use the air condi- tioning system to increase the tem- perature around the front camera.
The area in front of the front camera is obstructed, such as when the hood is open or a sticker is attached to the part of the windshield in front of the front camera.	Close the hood, remove the sticker, etc. to clear the obstruction.
When “Pre-Collision System Radar In Self Calibration Unavailable See Owner’s Manual” is displayed	Check whether there is attached materials on the radar sensor and radar sensor cover, and if there is, remove it.

In the following situations, if the situation has changed (or the vehicle has been driven for some time) and the normal operating conditions are detected, the message will disappear and the system will become operational.

If the message does not disappear, contact your Toyota dealer.
When the temperature around the radar sensor is outside of the operational range, such as when the vehicle is in the sun or in an extremely cold environment
When the front camera cannot detect objects in front of the vehicle, such as when driving in the dark, snow, or fog, or when bright lights are shining into the front camera
Depending on the conditions in the vicinity of the vehicle, the radar may judge the surrounding environment cannot be properly recognized. In that case, “Pre-Collision System Unavailable See Owner’s Manual” is displayed.

PCS (Pre-Collision System)

The pre-collision system uses a radar sensor and front camera to detect objects in front of the vehicle. When the system determines that the possibility of a frontal collision with an object is high, a warning operates to urge the driver to take evasive action and the potential brake pressure is increased to help the driver avoid the collision. If the system determines that the possibility of a frontal collision with an object is extremely high, the brakes are automatically applied to help avoid the collision or help reduce the impact of the collision. The pre-collision system can be disabled/enabled and the warning timing can be changed.

Detectable objects

The system can detect the following (The detectable objects differs depending on the function.):

Vehicles
Bicyclists
Pedestrians

System functions

Pre-collision warning

When the system determines that the possibility of a frontal collision is high, a buzzer will sound and a warning message will be displayed on the multiinformation display to urge the driver to take evasive action.

Pre-collision brake assist

When the system determines that the possibility of a frontal collision is high, the system applies greater braking force in relation to how strongly the brake pedal is depressed.

Pre-collision braking

If the system determines that the possibility of a frontal collision is extremely high, the brakes are automatically applied to help avoid the collision or reduce the impact of the collision.

Emergency steering assist

If the system determines that the possibility of a frontal collision is high and that there is sufficient space for the vehicle to be steered into within its lane, and the driver has begun evasive maneuver or steering, emergency steering assist will assist the steering movements to help enhance the vehicle stability and for lane departure prevention. During operation, the indicator will illuminate in green.

Intersection right/left turn assistance

If the system determines that there is a high possibility of a collision in the following situations, it will assist with Pre-collision warning and, if necessary Pre-collision braking. Depending on the configuration of the intersection, it may not be possible to support.

When you turn right/left at an intersection and cross the path of an oncoming vehicle
When you turn right/left, pedestrian is detected in the forward direction and estimated to enter your vehicle’s path (bicyclists are not detected.)

WARNING

Limitations of the pre-collision system

The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings.
Do not use the pre-collision system instead of normal braking operations under any circumstances. This system will not prevent collisions or lessen collision damage or injury in every situation. Do not overly rely on this system. Failure to do so may lead to an accident, resulting in death or serious injury.
Although this system is designed to help avoid a collision or help reduce the impact of the collision, its effectiveness may change according to various conditions, therefore the system may not always be able to achieve the same level of performance. Read the following conditions carefully. Do not overly rely on this system and always drive carefully.
Conditions under which the system may operate even if there is no possibility of a collision:
Conditions under which the system may not operate properly:
Do not attempt to test the operation of the pre-collision system yourself. Depending on the objects used for testing (dummies, cardboard objects imitating detectable objects, etc.), the system may not operate properly, possibly leading to an accident.

WARNING

Pre-collision braking
When the pre-collision braking function is operating, a large amount of braking force will be applied.
If the vehicle is stopped by the operation of the pre-collision braking function, the pre-collision braking function operation will be canceled after approximately 2 seconds. Depress the brake pedal as necessary.
The pre-collision braking function may not operate if certain operations are performed by the driver. If the accelerator pedal is being depressed strongly or the steering wheel is being turned, the system may determine that the driver is taking evasive action and possibly prevent the pre-collision braking function from operating.
In some situations, while the pre-collision braking function is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly or the steering wheel is turned and the system determines that the driver is taking evasive action.
If the brake pedal is being depressed, the system may determine that the driver is taking evasive action and possibly delay the operation timing of the pre-collision braking function.
Emergency steering assist
As emergency steering assist operation will be canceled when the system determines that lane departure prevention function has been completed.
Emergency steering assist may not operate or may be cancel in the following cases as the system may determine the driver is taking actions.
If the accelerator pedal is being depressed strongly, the steering wheel is being operated sharply, the brake pedal is being depressed or the turn signal lever is being operated. In this case, the system may determine that the driver is taking evasive action and the emergency steering assist may not operate.
In some situations, while the emergency steering assist is operating, operation of the function may be canceled if the accelerator pedal is depressed strongly, the steering wheel is operated sharply or the brake pedal is being depressed and the system determines that the driver is taking evasive action.
When the emergency steering assist is operating, if the steering wheel is held firmly or is operated in the opposite direction to that which the system is generating torque, the function may be canceled

WARNING

When to disable the pre-collision system
In the following situations, disable the system, as it may not operate properly, possibly leading to an accident resulting in death or serious injury:
When the vehicle is being towed
When your vehicle is towing another vehicle
When transporting the vehicle via truck, boat, train or similar means of transportation
When the vehicle is raised on a lift with the engine running and the tires are allowed to rotate freely
When inspecting the vehicle using a drum tester such as a chassis dynamometer or speedometer tester, or when using an on vehicle wheel balancer
When a strong impact is applied to the front bumper or front grille, due to an accident or other reasons
If the vehicle cannot be driven in a stable manner, such as when the vehicle has been in an accident or is malfunctioning
When the vehicle is driven in a sporty manner or off-road
When the tires are not properly inflated
When the tires are very worn
When tires of a size other than specified are installed
When tire chains are installed
When a compact spare tire or an emergency tire puncture repair kit is used
If equipment (snow plow, etc.) that may obstruct the radar sensor or front camera is temporarily installed to the vehicle

Changing settings of the pre-collision system

Enabling/disabling the pre-collision system
The pre-collision system can be enabled/disabled on of the multi-information display. The system is automatically enabled each time the engine switch is turned to IGNITION ON mode. If the system is disabled, the PCS warning light will turn on and a message will be displayed on the multi-information display.

Changing the pre-collision warning timing
The pre-collision warning timing can be changed on of the multi-information display. The warning timing setting is retained when the engine switch is turned off. However, if the pre-collision system is disabled and re-enabled, the operation timing will return to the default setting (middle). If the pre-collision warning timing is changed, emergency steering assist timing will also be changed accordingly. If late is selected, emergency steering assist would not operate in case of an emergency.

Early
Middle This is the default setting.
Late

Operational conditions for each pre-collision function

The pre-collision system is enabled and the system determines that the possibility of a frontal collision with a detected object is high. The system may not operate in the following situations:

If a battery terminal has been disconnected and reconnected and then the vehicle has not been driven for a certain amount of time
If the shift lever is in R
When the VSC OFF indicator is illuminated (only the pre-collision warning function will be operational) The operation speeds and operation cancellation for each function is listed below.

Pre-collision warning

Detectable objects	Vehicle speed	Relative speed between your vehicle and object
Preceding and stopped vehicles	Approx. 7 to 110 mph (10 to 180 km/h)	Approx. 7 to 110 mph (10 to 180 km/h)
Oncoming vehi- cles	Approx. 7 to 110 mph (10 to 180 km/h)	Approx. 13 to 110 mph (20 to 180 km/h)
Bicyclists and pedestrians	Approx. 7 to 50 mph (10 to 80 km/h)	Approx. 7 to 50 mph (10 to 80 km/h)

Pre-collision brake assist

Detectable objects

Vehicle speed

Relative speed between your vehicle and object

Preceding and stopped vehicles

Approx. 20 to 110 mph (30

to 180 km/h)

Approx. 20 to 110

mph (30 to 180 km/h)

Bicyclists and pedestrians

Approx. 20 to 50 mph (30 to

80 km/h)

Approx. 20 to 50 mph

(30 to 80 km/h)

Pre-collision braking

Detectable objects	Vehicle speed	Relative speed between your vehicle and object
Preceding and stopped vehicles	Approx. 7 to 110 mph (10 to 180 km/h)	Approx. 7 to 110 mph (10 to 180 km/h)
Oncoming vehi- cles	Approx. 7 to 110 mph (10 to 180 km/h)	Approx. 13 to 110 mph (20 to 180 km/h)
Bicyclists and pedestrians	Approx. 7 to 50 mph (10 to 80 km/h)	Approx. 7 to 50 mph (10 to 80 km/h)

If either of the following occur while the pre-collision braking function is operating, it will be canceled:

The accelerator pedal is depressed strongly.
The steering wheel is turned sharply or abruptly.

Emergency steering assist

When the turn signal lights are flashing, emergency steering assist will not operate in case of an emergency.

Detectable objects

Vehicle speed

Relative speed between your vehicle and object

Preceding and stopped vehicles, bicyclists and pedestrians

Approx. 25 to 50 mph (40 to

80 km/h)

Approx. 25 to 50 mph

(40 to 80 km/h)

If any of the following occur while the emergency steering assist function is operating, it will be canceled:

The accelerator pedal is depressed strongly.
The steering wheel is turned sharply or abruptly.
The brake pedal is depressed.

Intersection right/left turn assistance (pre-collision warning)

When the turn signal lights are not flashing, support for turning left or right at an intersection which targets oncoming vehicles does not work.

Detectable objects

Vehicle speed

Oncoming vehi- cle speed

Relative speed between your vehicle and object

Oncoming vehicles

Approx. 7 to 15

mph (10 to 25 km/h)

Approx. 20 to 35

mph (30 to 55 km/h)

Approx. 25 to 50

mph (40 to 80 km/h)

Pedestrians

Approx. 7 to 15

mph (10 to 25 km/h)

Approx. 7 to 15

mph (10 to 25 km/h)

Intersection right/left turn assistance (pre-collision braking)
When the turn signal lights are not flashing, support for turning left or right at an intersection which targets oncoming vehicles does not work

Detectable objects

Vehicle speed

Oncoming vehi- cle speed

Relative speed between your vehicle and object

Oncoming vehicles

Approx. 10 to 15

mph (15 to 25 km/h)

Approx. 20 to 28

mph (30 to 45 km/h)

Approx. 28 to 43

mph (45 to 70 km/h)

Pedestrians

Approx. 7 to 15

mph (10 to 25 km/h)

Approx. 7 to 15

mph (10 to 25 km/h)

Object detection function

The system detects objects based on their size, profile, motion, etc. However, an object may not be detected depending on the surrounding brightness and the motion, posture, and angle of the detected object, preventing the system from operating properly. The illustration shows an image of detectable objects.

Conditions under which the system may operate even if there is no possibility of a collision

In some situations such as the following, the system may determine that there is a possibility of a frontal collision and operate.
When passing a detectable object, etc.
When changing lanes while overtaking a detectable object, etc.
When rapidly closing on a detectable object, etc.
When approaching objects on the roadside, such as detectable objects, guardrails, utility poles, trees, or walls
When there are patterns or paint in front of your vehicle that may be mistaken for a detectable object
When the front of your vehicle is hit by water, snow, dust, etc.
When approaching a detectable object in an adjacent lane or on the roadside, such as when changing the course of travel or driving on a winding road
When there is a detectable object or other object by the roadside at the entrance of a curve
When overtaking a detectable object that is changing lanes or making a right/left turn
When passing a detectable object in an oncoming lane that is stopped to make a right/left turn
When a detectable object approaches very close and then stops before entering the path of your vehicle
If the front of your vehicle is raised or lowered, such as when on an uneven or undulating road surface
When driving on a road surrounded by a structure, such as in a tunnel or on an iron bridge
When there is a metal object (manhole cover, steel plate, etc.), steps, or a protrusion in front of your vehicle When passing under an object (road sign, billboard, etc.)
When approaching an electric toll gate barrier, parking area barrier, or other barrier that opens and closes
When using an automatic car wash When driving through or under objects that may contact your vehicle, such as thick grass, tree branches, or a banner When driving through steam or smoke
When driving near an object that reflects radio waves, such as a large truck or guardrail
When driving near a TV tower, broadcasting station, electric power plant, radar equipped vehicles, etc., or other location where strong radio waves or electrical noise may be present
When there are many things which can reflect the radio waves of the radar in the vicinity (tunnels, truss bridges, gravel roads, snow covered road that have tracks, etc.)
While making a right/left turn, when an oncoming vehicle or a crossing pedestrian has already exited the path of your vehicle
While making a right/left turn, closely in front of an oncoming vehicle or a crossing pedestrian.
While making a right/left turn, when an oncoming vehicle or a crossing pedestrian stops before entering the path of your vehicle
While making a right/left turn, when an oncoming vehicle turns right/left in front of your vehicle While steering into the direction of oncoming traffic

Situations in which the system may not operate properly

In some situations such as the following, an object may not be detected by the radar sensor and front camera, preventing the system from operating properly:
When a detectable object is approaching your vehicle
When your vehicle or a detectable object is wobbling
If a detectable object makes an abrupt maneuver (such as sudden swerving, acceleration or deceleration)
When your vehicle approaches a detectable object rapidly When a detectable object is not directly in front of your vehicle When a detectable object is near a wall, fence, guardrail, manhole cover, vehicle, steel plate on the road, etc.
When a detectable object is under a structure
When part of a detectable object is hidden by an object, such as large baggage, an umbrella, or guardrail
When there are many things which can reflect the radio waves of the radar in the vicinity (tunnels, truss bridges, gravel roads, snow covered road that have tracks, etc.)
When there is an effect on the radio waves to the radar that is installed on another vehicle
When multiple detectable objects are close together
If the sun or other light is shining directly on a detectable object
When a detectable object is a shade of white and looks extremely bright
When a detectable object appears to be nearly the same color or brightness as its surroundings
If a detectable object cuts or suddenly emerges in front of your vehicle
When the front of your vehicle is hit by water, snow, dust, etc.
When a very bright light ahead, such as the sun or the headlights of oncoming traffic, shines directly into the front camera
When approaching the side or front of a vehicle ahead
If a vehicle ahead is a motorcycle If a vehicle ahead is narrow, such as a personal mobility vehicle
If a preceding vehicle has a small rear end, such as an unloaded truck
If a preceding vehicle has a low rear end, such as a low bed trailer If a vehicle ahead has extremely high ground clearance
If a vehicle ahead is carrying a load which protrudes past its rear bumper
If a vehicle ahead is irregularly shaped, such as a tractor or side car
If a vehicle ahead is a child sized bicycle, a bicycle that is carrying a large load, a bicycle ridden by more than one person, or a uniquely shaped bicycle (bicycle with a child seat, tandem bicycle, etc.)
If a pedestrian/ or the riding height of a bicyclist ahead is shorter than approximately 3.2 ft. (1 m) or taller than approximately 6.5 ft. (2 m)
If a pedestrian/bicyclist is wearing oversized clothing (a rain coat, long skirt, etc.), making their silhouette obscure
If a pedestrian is bending forward or squatting or bicyclist is bending forward
If a pedestrian/bicyclist is moving fast
If a pedestrian is pushing a stroller, wheelchair, bicycle or other vehicle

When driving in inclement weather such as heavy rain, fog, snow or a sandstorm
When driving through steam or smoke
When the surrounding area is dim, such as at dawn or dusk, or while at night or in a tunnel, making a detectable object appear to be nearly the same color as its surroundings
When driving in a place where the surrounding brightness changes suddenly, such as at the entrance or exit of a tunnel
After the engine has started the vehicle has not been driven for a certain amount of time
While making a left/right turn and for a few seconds after making a left/ right turn
While driving on a curve and for a few seconds after driving on a curve
If your vehicle is skidding If the front of the vehicle is raised or lowered If the wheels are misaligned
If a wiper blade is blocking the front camera
The vehicle is being driven at extremely high speeds
When driving on a hill
If the radar sensor or front camera is misaligned
When driving in a traffic lane separated by more than one lane where oncoming vehicles are driving while making a right/left turn
When largely out of place with the opposite facing targeted oncoming vehicle during a right/left turn
While making a right/left turn, when a pedestrian approaches from behind or side of your vehicle
In addition to the above, in some situations, such as the following, the emergency steering assist may not operate.
When the white (yellow) lane lines are difficult to see, such as when they are faint, diverging/merging, or a shadow is cast upon them
When the lane is wider or narrower than normal
When there is a light and dark pattern on the road surface, such as due to road repairs
When the target is too close
When there is insufficient safe or unobstructed space for the vehicle to be steered into
If oncoming vehicle is present
If VSC function is operating

In some situations such as the following, sufficient braking force or steering force may not be obtained, preventing the system from performing properly:

If the braking functions cannot operate to their full extent, such as when the brake parts are extremely cold, extremely hot, or wet
If the vehicle is not properly maintained (brakes or tires are excessively worn, improper tire inflation pressure, etc.)
When the vehicle is being driven on a gravel road or other slippery surface
When the road surface has deep wheel tracks
When driving on a hill road
When driving on a road that has inclines to the left or right

If VSC is disabled

If VSC is disabled, the pre-collision brake assist and pre-collision braking functions are also disabled.
The PCS warning light will turn on and “VSC Turned Off Pre-Collision Brake System Unavailable” will be displayed on the multi-information display

LTA (Lane Tracing Assist)

Summary of functions

While driving on a road with clear white (yellow) lane lines, the LTA system warns the driver if the vehicle may deviate from the current lane or course*, and also can slightly operate the steering wheel to help avoid deviation from the lane or course*. Also, while the dynamic radar cruise control with full-speed range is operating, this system will operate the steering wheel to maintain the vehicle’s lane position. The LTA system recognizes white (yellow) lane lines or a course* using the front camera. Additionally, it detects preceding vehicles using the front camera and radar.

WARNING

Before using LTA system
Do not rely solely upon the LTA system.
The LTA system does not automatically drive the vehicle or reduce the amount of attention that must be paid to the area in front of the vehicle.
The driver must always assume full responsibility for driving safely by paying careful attention to the surrounding conditions and operating the steering wheel to correct the path of the vehicle.
Also, the driver must take adequate breaks when fatigued, such as from driving for a long period of time.
Failure to perform appropriate driving operations and pay careful attention may lead to an accident, resulting in death or serious injury.

WARNING

Situations unsuitable for LTA system In the following situations, use the LTA switch to turn the system off. Failure to do so may lead to an accident, resulting in death or serious injury.
Vehicle is driven on a road surface which is slippery due to rainy weather, fallen snow, freezing, etc.
Vehicle is driven on a snow-covered road.
White (yellow) lines are difficult to see due to rain, snow, fog, dust, etc.
Vehicle is driven in a temporary lane or restricted lane due to construction work.
Vehicle is driven in a construction zone.
A spare tire, tire chains, etc. are equipped.
When the tires have been excessively worn, or when the tire inflation pressure is low.
During emergency towing
Preventing LTA system malfunctions and operations performed by mistake
Do not modify the headlights or place stickers, etc. on the surface of the lights.
Do not modify the suspension etc. If the suspension etc. needs to be replaced, contact your Toyota dealer.
Do not install or place anything on the hood or grille. Also, do not install a grille guard (bull bars, kangaroo bar, etc.).
If your windshield needs repairs, contact your Toyota dealer.

WARNING

Conditions in which functions may not operate properly
In the following situations, the functions may not operate properly and the vehicle may depart from its lane. Drive safely by always paying careful attention to your surroundings and operate the steering wheel to correct the path of the vehicle without relying solely on the functions.
When the follow-up cruising display is displayed and the preceding vehicle is swaying. (Your vehicle may sway accordingly and depart from the lane.)
When the follow-up cruising display is displayed and the preceding vehicle departs from its lane. (Your vehicle may follow the preceding vehicle and depart from the lane.)
When the follow-up cruising display is displayed and the preceding vehicle is being driven extremely close to the left/right lane line. (Your vehicle may follow the preceding vehicle and depart from the lane.)
Vehicle is being driven around a sharp curve.
When the follow-up cruising display is displayed and the preceding vehicle changes lanes. (Your vehicle may follow the preceding vehicle and also change lanes.)
Objects or patterns that could be mistaken for white (yellow) lines are present on the side of the road (guardrails, reflective poles, etc.).

WARNING

Vehicle is driven where the road diverges, merges, etc.
Repair marks of asphalt, white (yellow) lines, etc. are present due to road repair.
There are shadows on the road that run parallel with, or cover, the white (yellow) lines.
The vehicle is driven in an area without white (yellow) lines, such as in front of a tollgate or checkpoint, or at an intersection, etc.
The white (yellow) lines are cracked, “Botts’ dots”, “Raised pavement marker” or stones are present.
The white (yellow) lines cannot be seen or are difficult to see due to sand, etc.
The vehicle is driven on a road surface that is wet due to rain, puddles, etc.
The traffic lines are yellow (which may be more difficult to recognize than lines that are white).
The white (yellow) lines cross over a curb, etc.
The vehicle is driven on a bright surface, such as concrete.
If the edge of the road is not clear or straight.
The vehicle is driven on a surface that is bright due to reflected light, etc.
The vehicle is driven in an area where the brightness changes suddenly, such as at the entrances and exits of tunnels, etc.

WARNING

Light from the headlights of an oncoming vehicle, the sun, etc. enters the camera.
The vehicle is driven on a slope.
The vehicle is driven on a road which tilts left or right, or a winding road.
The vehicle is driven on an unpaved or rough road.
The traffic lane is excessively narrow or wide.
The vehicle is extremely tilted due to carrying heavy luggage or having improper tire pressure.
The distance to the preceding vehicle is extremely short.
The vehicle is moving up and down a large amount due to road conditions during driving (poor roads or road seams).
When driving in a tunnel or at night with the headlights off or when a headlight is dim due to its lens being dirty or it being misaligned.
The vehicle is struck by a crosswind.
The vehicle is affected by wind from a vehicle driven in a nearby lane.
The vehicle has just changed lanes or crossed an intersection.
Tires which differ by structure, manufacturer, brand or tread pattern are used.
When tires of a size other than specified are installed.
Snow tires, etc. are equipped.
The vehicle is being driven at extremely high speeds.

Functions included in LTA system

Lane departure alert function

When the system determines that the vehicle might depart from its lane or course*, a warning is displayed on the multi-information display, and a warning buzzer will sound to alert the driver. When the warning buzzer sounds, check the area around your vehicle and carefully operate the steering wheel to move the vehicle back to the center of the lane. Vehicle with BSM: When the system determines that the vehicle might depart from its lane and that the possibility of a collision with an overtaking vehicle in the adjacent lane is high, the lane departure alert will operate even if the turn signals are operating. *: Boundary between asphalt and the side of the road, such as grass, soil, or a curb

Steering assist function

When the system determines that the vehicle might depart from its lane or course*, the system provides assistance as necessary by operating the steering wheel in small amounts for a short period of time to keep the vehicle in its lane. Vehicle with BSM: When the system determines that the vehicle might depart from its lane and that the possibility of a collision with an overtaking vehicle in the adjacent lane is high, the steering assist function will operate even if the turn signals are operating. *: Boundary between asphalt and the side of the road, such as grass, soil, or a curb

Vehicle sway warning function

When the vehicle is swaying within a lane, the warning buzzer will sound and a message will be displayed on the multi-information display to alert the driver.

Lane centering function

This function is linked with dynamic radar cruise control with full-speed range and provides the required assistance by operating the steering wheel to keep the vehicle in its current lane. When dynamic radar cruise control with full-speed range is not operating, the lane centering function does not operate. In situations where the white (yellow) lane lines are difficult to see or are not visible, such as when in a traffic jam, this function will operate to help follow a preceding vehicle by monitoring the position of the preceding vehicle.

Turning LTA system on

Press the LTA switch to turn the LTA system on. The LTA indicator illuminates and a message is displayed on the multiinformation display. Press the LTA switch again to turn the LTA system off. When the LTA system is turned on or off, operation of the LTA system continues in the same condition the next time the engine is started

Indications on the multi-information display

LTA indicator
- The illumination condition of the indicator informs the driver of the system operation status.
- Illuminated in white: LTA system is operating. Illuminated in green: Steering wheel assistance of the steering assist function or lane centering function is operating.
- Flashing in orange: Lane departure alert function is operating.
Operation display of steering wheel operation support
- Displayed when the multi-information display is switched to the driving assist system information screen.
- Indicates that steering wheel assistance of the steering assist function or lane centering function is operating.
- Both outer sides of the lane are displayed: Indicates that steering wheel assist of the lane centering function is operating.
- One outer side of the lane is displayed: Indicates that steering wheel assist of the steering assist function is operating.
- Both outer sides of the lane are flashing: Alerts the driver that their input is necessary to stay in the center of the lane (lane centering function).
Lane departure alert function display
- Displayed when the multi-information display is switched to the driving assist system information screen.
Inside of displayed lines is white
- Indicates that the system is recognizing white (yellow) lines or a course*. When the vehicle departs from its lane, the white line displayed on the side the vehicle departs from flashes orange.
Inside of displayed lines is black
- Indicates that the system is not able to recognize white (yellow) lines or a course* or is temporarily canceled.
Follow-up cruising display
- Displayed when the multi-information display is switched to the driving assist system information screen.

Indicates that steering assist of the lane centering function is operating by monitoring the position of a preceding vehicle. When the follow-up cruising display is displayed, if the preceding vehicle moves, your vehicle may move in the same way. Always pay careful attention to your surroundings and operate the steering wheel as necessary to correct the path of the vehicle and ensure safety.

Operation conditions of each function

Lane departure alert function

This function operates when all of the following conditions are met.

LTA is turned on.
Vehicle speed is approximately 32 mph (50 km/h) or more.*1
System recognizes white (yellow) lane lines or a course*2. (When a white [yellow] line or course*2 is recognized on only one side, the system will operate only for the recognized side.)
Width of traffic lane is approximately 9.8 ft. (3 m) or more.
Turn signal lever is not operated. (Vehicle with BSM: Except when another vehicle is in the lane on the side where the turn signal was operated)
Vehicle is not being driven around a sharp curve.
No system malfunctions are detected.

The function operates even if the vehicle speed is less than approximately 32 mph (50 km/h) when the lane centering function is operating.
Boundary between asphalt and the side of the road, such as grass, soil, or a curb

Steering assist function

This function operates when all of the following conditions are met in addition to the operation conditions for the lane departure alert function.

Vehicle is not accelerated or decelerated by a fixed amount or more.
Steering wheel is not operated with a steering force level suitable for changing lanes.
ABS, VSC, TRAC and PCS are not operating.
TRAC or VSC is not turned off.

Vehicle sway warning function

This function operates when all of the following conditions are met.

Setting for “Sway Warning” in of the multi-information display is set to “On”
Vehicle speed is approximately 32 mph (50 km/h) or more.
Width of traffic lane is approximately 9.8 ft. (3 m) or more.
No system malfunctions are detected

Lane centering function

This function operates when all of the following conditions are met.

LTA is turned on.
Setting for “Lane Center” in of the multi-information display is set to “ON”.
This function recognizes white (yellow) lane lines or the position of a preceding vehicle (except when the preceding vehicle is small, such as a motorcycle)
The dynamic radar cruise control with full-speed range is operating in vehicle-to-vehicle distance control mode.
Width of traffic lane is approximately 10 to 13 ft. (3 to 4 m).
Turn signal lever is not operated.
Vehicle is not being driven around a sharp curve.
No system malfunctions are detected.
Vehicle does not accelerate or decelerate by a fixed amount or more.
Steering wheel is not operated with a steering force level suitable for changing lanes.
ABS, VSC, TRAC and PCS are not operating.
TRAC or VSC is not turned off.
Hands off steering wheel warning is not displayed.
The vehicle is being driven in the center of a lane.
Steering assist function is not operating.

Temporary cancelation of functions

When operation conditions are no longer met, a function may be temporarily canceled. However, when the operation conditions are met again, operation of the function is automatically restored.
If the operation conditions are no longer met while the lane centering function is operating, the buzzer may sound to indicate that the function has been temporarily canceled.
Steering assist function/lane centering function
Depending on the vehicle speed, lane departure situation, road conditions, etc., the driver may not feel the function is operating or the function may not operate at all.
The steering control of the function is overridden by the driver’s steering wheel operation.
Do not attempt to test the operation of the steering assist function.
Lane departure alert function
The warning buzzer may be difficult to hear due to external noise, audio playback, etc.
If the edge of the course* is not clear or straight, the lane departure alert function may not operate.
Vehicle with BSM: It may not be possible for the system to determine if there is a danger of a collision with a vehicle in an adjacent lane.
Do not attempt to test the operation of the lane departure alert function. *: Boundary between asphalt and the side of the road, such as grass, soil, or a curb

Hands off steering wheel warning

In the following situations, a warning message urging the driver to hold the steering wheel and the symbol shown in the illustration are displayed on the multi-information display to warn the driver. The warning stops when the system determines that the driver holds the steering wheel. Always keep your hands on the steering wheel when using this system, regardless of warnings.

When the system determines the driver is not holding the steering wheel while the lane centering function is operating. If the driver continues to keep their hands off of the steering wheel, the buzzer sounds, the driver is warned and the function is temporarily canceled. This warning also operates in the same way when the driver continuously operates the steering wheel only a small amount.
When the system determines that the vehicle may deviate from the lane while driving around a curve while the lane centering function is operating. Depending on the vehicle condition and road conditions, the warning may not operate. Also, if the system determines that the vehicle is driving around a curve, warnings will occur earlier than during straight-lane driving.
When the system determines that the driver is driving without holding the steering wheel while the steering wheel assist of the steering assist function is operating. If the driver continues to keep their hands off of the steering wheel and the steering wheel assist is operating, the buzzer sounds and the driver is warned. Each time the buzzer sounds, the continuing time of the buzzer becomes longer.

Vehicle sway warning function

When the system determines that the vehicle is swaying while the vehicle sway warning function is operating, a buzzer sounds and a warning message urging the driver to rest and the symbol shown in the illustration are simultaneously displayed on the multi-information display.

Warning message

If the following warning message is displayed on the multi-information display and the LTA indicator illuminates in orange, follow the appropriate troubleshooting procedure. Also, if a different warning message is displayed, follow the instructions displayed on the screen.

“LTA Malfunction Visit Your Dealer” The system may not be operating properly. Have the vehicle inspected by your Toyota dealer.
“LTA Unavailable” The system is temporarily canceled due to a malfunction in a sensor other than the front camera. Turn the LTA system off, wait for a little while, and then turn the LTA system back on.
“LTA Unavailable at Current Speed” The function cannot be used as the vehicle speed exceeds the LTA operation range. Drive slower.

Customization
Function settings can be changed

RSA (Road Sign Assist)

Summary of function

The RSA system recognizes specific road signs using the front camera and/or navigation system (when speed limit information is available) to provide information to the driver via the display. If the system judges that the vehicle is being driven over the speed limit, performing prohibited actions, etc. according to the recognized road signs, it notifies the driver through a visual notification and notification buzzer.

WARNING

Before using the RSA

Do not rely solely upon the RSA system. RSA is a system which supports the driver by providing information, but it is not a replacement for a driver’s own vision and awareness. Drive safely by always paying careful attention to the traffic rules.

Indication on the multi-information display

When the front camera recognizes a sign and/or information of a sign is available from the navigation system, the sign will be displayed on the multi-information display.

When the driving assist system information is selected, a maximum of 3 signs can be displayed.
When a tab other than the driving assist system information is selected, the following types of road signs will be displayed.
Speed limit sign
Do Not Enter sign (when notification is necessary)

If signs other than speed limit signs are recognized, they will be displayed in an overlapping stack under the current speed limit sign.

Supported types of road signs

The following types of road signs, including electronic signs and blinking signs, are recognized. A non-official or a recently introduced traffic sign may not be recognized.

Notification function

In the following situations, the RSA system will notify the driver.

When the vehicle speed exceeds the speed notification threshold of the speed limit sign displayed, the sign display will be emphasized and a buzzer will sound.
When the RSA system recognizes a do not enter sign and determines that your vehicle has entered a no-entry area, the displayed sign will flash and a buzzer will sound.

Depending on the situation, a notification function may not operate properly.

Setting procedure

Press

of the meter control switches, select
Press of the meter control switches, select

.
Press of the meter control switch.
Each time is pressed, the function changes on/off.

Automatic turn-off of RSA sign display

In the following situations, a displayed speed limit sign and/or do not enter sign will stop being displayed automatically:

No sign has been recognized for a certain distance.
The road changes due to a left or right turn, etc.
In the following situations, stop and yield signs will stop being displayed automatically:
The system determines that your vehicle has passed the sign.
The road changes due to a left or right turn, etc.

Conditions in which the function may not operate or detect correctly

In the following situations, RSA does not operate normally and may not recognize signs, display the incorrect sign, etc. However, this does not indicate a malfunction.

The front camera is misaligned due to a strong impact being applied to the sensor, etc.
Dirt, snow, stickers, etc. are on the windshield near the front camera.
In inclement weather such as heavy rain, fog, snow or sand storms
Light from an oncoming vehicle, the sun, etc. enters the front camera.
The sign is dirty, faded, tilted or bent.
The contrast of electronic sign is low.
All or part of the sign is hidden by the leaves of a tree, a pole, etc.
The sign is only visible to the front camera for a short amount of time.
The driving scene (turning, lane change, etc.) is judged incorrectly.
If a sign not appropriate for the currently traveled lane, but the sign exists directly after a freeway branches, or in an adjacent lane just before merging.
Stickers are attached to the rear of the preceding vehicle.
A sign resembling a system compatible sign is recognized.
Side road speed signs may be detected and displayed (if positioned in sight of the front camera) while the vehicle is traveling on the main road.
Roundabout exit road speed signs may be detected and displayed (if positioned in sight of the front camera) while traveling on a roundabout.
The front of the vehicle is raised or lowered due to the carried load.
The surrounding brightness is not sufficient or changes suddenly.
When a sign intended for trucks, etc. is recognized.
The navigation system map data is outdated.
The navigation system is not operating.
The speed information displayed on the meter and on the navigation system may be different due to the navigation system using map data.

Speed limit sign display
If the engine switch was last turned off while a speed limit sign was displayed on the multi-information display, the same sign displays again when the engine switch is turned to ON.

If “RSA Malfunction Visit Your Dealer” is shown
The system may be malfunctioning. Have the vehicle inspected by your Toyota dealer.

Customization
Some functions can be customized.

Dynamic radar cruise control with full speed range

Summary of functions

In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates, decelerates and stops to match the speed changes of the preceding vehicle even if the accelerator pedal is not depressed. In constant speed control mode, the vehicle runs at a fixed speed. Use the dynamic radar cruise control with full-speed range on freeways and highways.

Vehicle-to-vehicle distance control mode
Constant speed control mode

System Components

Meter display
- Multi-information display
- Set speed
- Indicators
Operation switches
- Vehicle-to-vehicle distance switch
- “+ RES” switch
- Cruise control main switch
- Cancel switch
- “- SET” switch

WARNING

Before using dynamic radar cruise control with full-speed range
Driving safely is the sole responsibility of the driver. Do not rely solely on the system, and drive safely by always paying careful attention to your surroundings.
The dynamic radar cruise control with full-speed range provides driving assistance to reduce the driver’s burden. However, there are limitations to the assistance provided.
Read the following conditions carefully.
Do not overly rely on this system and always drive carefully.
When the sensor may not be correctly detecting the vehicle ahead
Conditions under which the vehicle-to-vehicle distance control mode may not function correctly:
Set the speed appropriately depending on the speed limit, traffic flow, road conditions, weather conditions, etc. The driver is responsible for checking the set speed.
Even when the system is functioning normally, the condition of the preceding vehicle as detected by the system may differ from the condition observed by the driver.
Therefore, the driver must always remain alert, assess the danger of each situation and drive safely.
Relying solely on this system or assuming the system ensures safety while driving can lead to an accident, resulting in death or serious injury.
Switch the dynamic radar cruise control with full-speed range setting to off, using the cruise control main switch when not in use.

WARNING

Cautions regarding the driving assist systems Observe the following precautions, as there are limitations to the assistance provided by the system.
Failure to do so may cause an accident resulting in death or serious injury.
Assisting the driver to measure following distance The dynamic radar cruise control with full-speed range is only intended to help the driver in determining the following distance between the driver’s own vehicle and a designated vehicle traveling ahead. It is not a mechanism that allows careless or inattentive driving, and it is not a system that can assist the driver in low-visibility conditions.
It is still necessary for drivers to pay close attention to the vehicle’s surroundings.
Assisting the driver to judge proper following distance The dynamic radar cruise control with full-speed range determines whether the following distance between the driver’s own vehicle and a designated vehicle traveling ahead is within a set range. It is not capable of making any other type of judgement. Therefore, it is absolutely necessary for the driver to remain vigilant and to determine whether or not there is a possibility of danger in any given situation.
Assisting the driver to operate the vehicle The dynamic radar cruise control with full-speed range does not include functions which will prevent or avoid collisions with vehicles ahead of your vehicle. Therefore, if there is ever any possibility of danger, the driver must take immediate and direct control of the vehicle and act appropriately in order to ensure the safety of all involved.

WARNING

Situations unsuitable for dynamic radar cruise control with full-speed range Do not use dynamic radar cruise control with full-speed range in any of the following situations.
Doing so may result in inappropriate speed control and could cause an accident resulting in death or serious injury.
Roads where there are pedestrians, cyclists, etc.
In heavy traffic
On roads with sharp bends
On winding roads
On slippery roads, such as those covered with rain, ice or snow
On steep downhills, or where there are sudden changes between sharp up and down gradients Vehicle speed may exceed the set speed when driving down a steep hill.
At entrances to freeways and highways
When weather conditions are bad enough that they may prevent the sensors from detecting correctly (fog, snow, sandstorm, heavy rain, etc.)
When there is rain, snow, etc. on the front surface of the radar or front camera
In traffic conditions that require frequent repeated acceleration and deceleration
During emergency towing
When an approach warning buzzer is heard often

Driving in vehicle-to-vehicle distance control mode

This mode employs a radar to detect the presence of vehicles up to approximately 328 ft. (100 m) ahead, determines the current vehicleto- vehicle following distance, and operates to maintain a suitable following distance from the vehicle ahead. The desired vehicle-to-vehicle distance can also be set by operating the vehicle-to-vehicle distance switch. When driving on downhill slopes, the vehicle-to-vehicle distance may become shorter.

Example of constant speed cruising When there are no vehicles ahead The vehicle travels at the speed set by the driver.
Example of deceleration cruising and follow-up cruising When a preceding vehicle driving slower than the set speed appears

When a vehicle is detected running ahead of you, the system automatically decelerates your vehicle. When a greater reduction in vehicle speed is necessary, the system applies the brakes (the stop lights will come on at this time). The system will respond to changes in the speed of the vehicle ahead in order to maintain the vehicle-to-vehicle distance set by the driver. Approach warning warns you when the system cannot decelerate sufficiently to prevent your vehicle from closing in on the vehicle ahead. When the vehicle ahead of you stops, your vehicle will also stop (vehicle is stopped by system control). After the vehicle ahead starts off, pressing the “+ RES” switch or depressing the accelerator pedal (start-off operation) will resume follow-up cruising. If the start-off operation is not performed, system control continues to keep your vehicle stopped. When the turn signal lever is operated and your vehicle moves to an overtaking lane while driving at 50 mph (80 km/h) or more, the vehicle will accelerate to help to overtake a passing vehicle. The system’s identification of what is an overtaking lane may be determined solely based on the location of the steering wheel in the vehicle (left side driver position versus right side driver position.) If the vehicle is driven to a region where the overtaking lane is on a different side from where the vehicle is normally driven, the vehicle may accelerate when the turn signal lever is operated in the opposite direction to the overtaking lane (e.g., if the driver normally operates the vehicle in a region where the overtaking lane is to the right but then drives to a region where the overtaking lane is to the left, the vehicle may accelerate when the right turn signal is activated).

Example of acceleration When there are no longer any preceding vehicles driving slower than the set speed The system accelerates until the set speed is reached. The system then returns to constant speed cruising.

Setting the vehicle speed (vehicle-to-vehicle distance control mode

Press the cruise control main switch to activate the cruise control. Dynamic radar cruise control indicator will come on and a message will be displayed on the multi-information display. Press the switch again to deactivate the cruise control. If the cruise control main switch is pressed and held for 1.5 seconds or more, the system turns on in constant speed control mode.
Accelerate or decelerate, with accelerator pedal operation, to the desired vehicle speed (at or above approximately 20 mph [30 km/h]) and press the “- SET” switch to set the speed. Cruise control “SET” indicator will come on. The vehicle speed at the moment the switch is released becomes the set speed

Adjusting the set speed

Adjusting the set speed by the switch

To change the set speed, press the “+ RES” or “- SET” switch until the desired set speed is displayed.

Increases the speed
(Except when the vehicle has been stopped by system control in vehicle-to-vehicle distance control mode)

Decreases the speed
Fine adjustment: Press the switch. Large adjustment: Press and hold the switch to change the speed, and release when the desired speed is reached.

In the vehicle-to-vehicle distance control mode, the set speed will be increased or decreased as follows:

For U.S. mainland and Hawaii
Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed Large adjustment: Increases or decreases in 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 increments for as long as the switch is held

For Canada and Puerto Rico
Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6mph)*2 each time the switch is pressed Large adjustment: Increases or decreases in 5 mph (8 km/h)*1 or 5 km/h (3.1 mph)*2 increments for as long as the switch is held In the constant speed control mode, the set speed will be increased or decreased as follows: Fine adjustment: By 1 mph (1.6 km/h)*1 or 1 km/h (0.6 mph)*2 each time the switch is pressed Large adjustment: The speed will continue to change while the switch is held.

When the set speed is shown in “MPH”
When the set speed is shown in “km/h”

Increasing the set speed by the accelerator pedal

Accelerate with accelerator pedal operation to the desired vehicle speed
Press the “- SET” switch

Changing the vehicle-to-vehicle distance (vehicle-to-vehicle distance control mode)

Long
Medium
Short

Vehicle-to-vehicle distance settings (vehicle-to-vehicle distance control mode

Select a distance from the table below. Note that the distances shown correspond to a vehicle speed of 50 mph (80 km/h). Vehicle-to-vehicle distance increases/decreases in accordance with vehicle speed. When the vehicle is stopped by system control, the vehicle stops at a certain vehicle-to-vehicle distance depending on the situation.

Distance options	Vehicle-to-vehicle distance
Long	Approximately 160 ft. (50 m)
Medium	Approximately 130 ft. (40 m)
Short	Approximately 100 ft. (30 m)

Resuming follow-up cruising when the vehicle has been stopped by system control (vehicle-to-vehicle distance control mode)

After the vehicle ahead of you starts off, press the “+ RES” switch. Your vehicle will also resume follow- up cruising if the accelerator pedal is depressed after the vehicle ahead of you starts off.

Canceling and resuming the speed control

Pressing the cancel switch cancels the speed control. The speed control is also canceled when the brake pedal is depressed. (When the vehicle has been stopped by system control, depressing the brake pedal does not cancel the setting.)
Pressing the “+ RES” switch resumes the cruise control and returns vehicle speed to the set speed.

Approach warning (vehicle-to-vehicle distance control mode)

When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the display will flash and the buzzer will sound to alert the driver. An example of this would be if another driver cuts in front of you while you are following a vehicle. Depress the brake pedal to ensure an appropriate vehicle-tovehicle distance.

Warnings may not occur when

In the following instances, warnings may not occur even when the vehicle-to-vehicle distance is small.

When the speed of the preceding vehicle matches or exceeds your vehicle speed
When the preceding vehicle is traveling at an extremely slow speed
Immediately after the cruise control speed was set
When depressing the accelerator pedal

Curve speed reduction function

While driving in vehicle-to-vehicle distance control mode, this function will reduce the vehicle speed, if it is determined to be necessary.

Function operation

When the steering wheel begins to be turned, the vehicle speed will begin being reduced. When the steering wheel is returned to the center position, the vehicle speed reduction will end. Depending on the situation, the vehicle speed will then return to the vehicle-to-vehicle distance control mode set speed. In situations where vehicle-to-vehicle distance control needs to operate, such as when a preceding vehicle cuts in front of your vehicle, the curve speed reduction function will be canceled.

Operation display

Displayed when the vehicle speed is being reduced. When the vehicle speed reduction ends, the display will disappear.

Changing the settings of the curve speed reduction function

The curve speed reduction function can be enabled/disabled and the vehicle speed reduction strength can be adjusted on of the multi-information display. The setting will change each time the “OK” meter control switch is pressed.

Selecting constant speed control mode

With the cruise control off, press and hold the cruise control main switch for 1.5 seconds or more. Immediately after the switch is pressed, the dynamic radar cruise control indicator will come on. Afterwards, it switches to the cruise control indicator. Switching to constant speed control mode is only possible when operating the switch with the cruise control off.
Accelerate or decelerate, with accelerator pedal operation, to the desired vehicle speed (at or above approximately 20 mph [30 km/h]) and press the “- SET” switch to set the speed.

Cruise control “SET” indicator will come on. The vehicle speed at the moment the switch is released becomes the set speed. Adjusting the speed setting: Canceling and resuming the speed setting

Dynamic radar cruise control with full-speed range can be set when

The shift lever is in D.
The desired set speed can be set when the vehicle speed is approximately 20 mph (30 km/h) or more. (However, when the vehicle speed is set while driving at below approximately 20 mph [30 km/h], the set speed will be set to approximately 20 mph [30 km/h].)

Accelerating after setting the vehicle speed

The vehicle can accelerate by operating the accelerator pedal. After accelerating, the set speed resumes. However, during vehicle-to-vehicle distance control mode, the vehicle speed may decrease below the set speed in order to maintain the distance to the preceding vehicle.

When the vehicle stops while follow-up cruising

Pressing the “+ RES” switch while the vehicle ahead stops will resume follow- up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed.
If the vehicle ahead starts off within 3 seconds after your vehicle stops, follow- up cruising will be resumed.

Automatic cancelation of vehicle-to-vehicle distance control mode

Vehicle-to-vehicle distance control mode is automatically canceled in the following situations.

VSC is activated.
TRAC is activated for a period of time.
When the VSC or TRAC system is turned off.
The sensor cannot detect correctly because it is covered in some way.
When the brake control or output restriction control of a driving support system operates. (For example: Pre-Collision System, Drive-Start Control)
The parking brake is operated.
The vehicle is stopped by system control on a steep incline.

The following are detected when the vehicle has been stopped by system control:

The driver is not wearing a seat belt.
The driver’s door is opened.
The vehicle has been stopped for about 3 minutes If vehicle-to-vehicle distance control mode is automatically canceled for any reasons other than the above, there may be a malfunction in the system. Contact your Toyota dealer.

Automatic cancelation of constant speed control mode

Constant speed control mode is automatically canceled in the following situations:

Actual vehicle speed is more than approximately 10 mph (16 km/h) below the set vehicle speed.
Actual vehicle speed falls below approximately 20 mph (30 km/h).
VSC is activated.
TRAC is activated for a period of time.
When the VSC or TRAC system is turned off.
When the brake control or output restriction control of a driving support system operates. (For example: Pre-Collision System, Drive-Start Control) If constant speed control mode is automatically canceled for any reasons other than the above, there may be a malfunction in the system. Contact your Toyota dealer.
Situations in which the curve speed reduction function may not operate In situations such as the following, the curve speed reduction function may not operate:
When the vehicle is being driven around a gentle curve
When the accelerator pedal is being depressed
When the vehicle is being driven around an extremely short curve
Brake operation A brake operation sound may be heard and the brake pedal response may change, but these are not malfunctions.

Situations in which the curve speed reduction function may not operate

In situations such as the following, the curve speed reduction function may not operate:

When the vehicle is being driven around a gentle curve
When the accelerator pedal is being depressed
When the vehicle is being driven around an extremely short curve

Brake operation

A brake operation sound may be heard and the brake pedal response may change, but these are not malfunctions

Warning messages and buzzers for dynamic radar cruise control with full-speed range

Warning messages and buzzers are used to indicate a system malfunction orto inform the driver of the need for caution while driving. If a warning message is shown on the multi-information display, read the message and follow the instructions.

When the sensor may not be correctly detecting the vehicle ahead

In the case of the following and depending on the conditions, operate the brake pedal when deceleration of the system is insufficient or operate the accelerator pedal when acceleration is required. As the sensor may not be able to correctly detect these types of vehicles, the approach warning may not be activated.

Vehicles that cut in suddenly
Vehicles traveling at low speeds
Vehicles that are not moving in the same lane
Vehicles with small rear ends (trailers with no load on board, etc.)

Motorcycles traveling in the same lane

When water or snow thrown up by the surrounding vehicles hinders the detecting of the sensor
When your vehicle is pointing upwards (caused by a heavy load in the luggage compartment, etc.)
Preceding vehicle has an extremely high ground clearance

Conditions under which the vehicle-to-vehicle distance control mode may not function correctly

In the case of the following conditions, operate the brake pedal (or accelerator pedal, depending on the situation) as necessary.
As the sensor may not be able to correctly detect vehicles ahead, the system may not operate properly.
When the road curves or when the lanes are narrow
When steering wheel operation or your position in the lane is unstable
When the vehicle ahead of you decelerates suddenly
When driving on a road surrounded by a structure, such as in a tunnel or on a bridge
While the vehicle speed is decreasing to the set speed after the vehicle accelerates by depressing the accelerator pedal

Situations in which the curve speed reduction function may not operate properly

In situations such as the following, the curve speed reduction function may not operate properly:
When the vehicle is being driven around a curve on an incline/decline
When the course of the vehicle differs from the shape of the curve
When the vehicle speed is excessively high when entering a curve
When the steering wheel is suddenly operated

BSM (Blind Spot Monitor)

Summary of the Blind Spot Monitor

The BSM (Blind Spot Monitor) function Assists the driver in making a decision when changing lanes
The RCTA (Rear Cross Traffic Alert) function

Multi-information display
- Turning the BSM function/RCTA function on/off.
Outside rear view mirror indicators
BSM function:
- When a vehicle is detected in the blind spot, the outside rear view mirror indicator comes on while the turn signal lever is not operated and the outside rear view mirror indicator flashes while the turn signal lever is operated.
RCTA function:
- When a vehicle approaching from the right or left rear of the vehicle is detected, the outside rear view mirror indicators flash.
“BSM” indicator/“RCTA” indicator When the BSM function/RCTA function is turned on, the indicator illuminates.
Audio system screen (RCTA function only)
- If a vehicle approaching from the right or left at the rear of the vehicle is detected, the RCTA icon
- for the detected side will be displayed.
RCTA buzzer (RCTA function only)
- When a vehicle approaching from the right or left rear of the vehicle is detected, a buzzer sounds from behind the rear seat.

Turning the BSM function/RCTA function on/off

Press of the meter control switches, select .
Press

of the meter control switched, select or .
Press

of the meter control switch.
Each time is pressed, the function changes on/off.

The outside rear view mirror indicators visibility

When under strong sunlight, the outside rear view mirror indicator may be difficult to see.

RCTA buzzer hearing

RCTA function may be difficult to hear over loud noises such as high audio volume.
When “Blind Spot Monitor Unavailable” or “Rear Cross Traffic Alert
Unavailable” are shown on the multi-information display
Ice, snow, mud, etc., may be attached to the rear bumper around the sensors.
The system should return to normal operation after removing the ice, snow, mud, etc., from the rear bumper. Additionally, the sensors may not operate normally when driving in extremely hot or cold environments.

When there is a malfunction in the Blind Spot Monitor

If a system malfunction is detected due to any of the following reasons, a warning message will be displayed:
- There is a malfunction with the sensors
- The sensors have become dirty
- The outside temperature is extremely high or low
- The sensor voltage has become abnormal

FCC

Certification for the Blind Spot Monitor

For vehicles sold in the U.S.A.

IFCC ID: HYQDNSRR003 I
IFCC ID: HYQDNSRR004 I

NOTE:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

This device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For vehicles sold in Canada

NOTE:
This device complies with Industry Canada’s RSS-310. Operation is subject to the condition that this device must not cause harmful interference and must accept any interference, including interference that may cause undesired operation of the device.

WARNING

Handling the radar sensor

One Blind Spot Monitor sensor is installed inside the left and right side of the vehicle rear bumper respectively. Observe the following to ensure the Blind Spot Monitor can function correctly.
Keep the sensor and its surrounding area on the bumper clean at all times. If a sensor or its surrounding area on the rear bumper is dirty or covered with snow, the Blind Spot Monitor may not operate and a warning
message will be displayed.
In this situation, clear off the dirt or snow and drive the vehicle with the operation conditions of the BSM function satisfied for approximately 60 minutes.
If the warning message does not disappear, have the vehicle inspected by your Toyota dealer
Do not subject a sensor or its surrounding area on the rear bumper to a strong impact.
If a sensor is moved even slightly off position, the system may malfunction and vehicles may not be detected correctly.

In the following situations, have your vehicle inspected by your Toyota dealer.

A sensor or its surrounding area is subject to a strong impact.
If the surrounding area of a sensor is scratched or dented, or part of them has become disconnected.
Do not disassemble the sensor.
Do not attach accessories or stickers to the sensor or surrounding area on the bumper.
Do not modify the sensor or surrounding area on the bumper.
Do not paint the rear bumper any color other than an official Toyota color.

BSM function

The BSM function uses radar sensors to detect vehicles that are traveling in an adjacent lane in the area that is usually not reflected in the outside rear view mirror (the blind spot), and advises the driver of the vehicles existence via the outside rear view mirror indicator.

BSM function detection areas

The areas that vehicles can be detected in are outlined below The range of the detection area is:

Approximately 1.6 ft. (0.5 m) to 11.5 ft. (3.5 m) from either side of the vehicle

The area between the side of the vehicle and 1.6 ft. (0.5 m) from the side of the vehicle cannot be detected.

Approximately 3.3 ft. (1 m) forward of the rear bumper
Approximately 9.8 ft. (3 m) from the rear bumper
Approximately 9.8 ft. (3 m) to 197 ft. (60 m) from the rear bumper

WARNING

Cautions regarding the use of the system
The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings.
The BSM function is a supplementary function which alerts the driver that a vehicle is present in the blind spot. Do not overly rely on the BSM function.
The function cannot judge if it is safe to change lanes, therefore over reliance could cause an accident resulting in death or serious injury.
According to conditions, the system may not function correctly. Therefore the driver’s own visual confirmation of safety is necessary.

The BSM function is operational when

The BSM function is turned on
Vehicle speed is greater than approximately 10 mph (16 km/h).

The BSM function will detect a vehicle when

A vehicle in an adjacent lane overtakes your vehicle.
You overtake a vehicle in adjacent lane slowly.
Another vehicle enters the detection area when it changes lanes.

Conditions under which the BSM function will not detect a vehicle

The BSM function is not designed to detect the following types of vehicles and/or objects:

Small motorcycles, bicycles, pedestrians, etc.*
Vehicles traveling in the opposite direction
Guardrails, walls, signs, parked vehicles and similar stationary objects*
Following vehicles that are in the same lane*
Vehicles driving 2 lanes across from your vehicle*
Vehicles which are being overtaken rapidly by your vehicle *: Depending on the conditions, detection of a vehicle and/or object may occur.

Conditions under which the BSM function may not function correctly

The BSM function may not detect vehicles correctly in the following conditions:
When the sensor is misaligned due to a strong impact to the sensor or its surrounding area
During bad weather such as heavy rain, fog, snow, etc.
When mud, snow, ice, a sticker, etc., is covering the sensor or surrounding area on the rear bumper
When driving on a road surface that is wet due to rain, standing water, snow, etc.
When there is a significant difference in speed between your vehicle and the vehicle that enters the detection area
When a vehicle is in the detection area from a stop and remains in the detection area as your vehicle accelerates
When driving up or down consecutive steep inclines, such as hills, a dip in the road, etc.
When driving on roads with sharp bends, consecutive curves, or uneven surfaces
When multiple vehicles approach with only a small gap between each vehicle
When vehicle lanes are wide, and the vehicle in the next lane is too far away from your vehicle
When the vehicle that enters the detection area is traveling at about the same speed as your vehicle
When there is a significant difference in height between your vehicle and the vehicle that enters the detection area
Immediately after the BSM function is turned on

Instances of the BSM function unnecessarily detecting a vehicle and/or object may increase under the following conditions:

When the sensor is misaligned due to a strong impact to the sensor or its surrounding area
When there is only a short distance between your vehicle and a guardrail, wall, etc.
When there is only a short distance between your vehicle and a following vehicle
When vehicle lanes are narrow and a vehicle driving 2 lanes across from your vehicle enters the detection area
When driving on roads with sharp bends, consecutive curves, or uneven surfaces
When items such as a bicycle carrier are installed on the rear of the vehicle

RCTA function

The RCTA functions when your vehicle is in reverse. It can detect other vehicles approaching from the right or left rear of the vehicle. It uses radar sensors to alert the driver of the other vehicle’s existence through flashing the outside rear view mirror indicators and sounding a buzzer.

Approaching vehicles
Detection areas

RCTA icon display
When a vehicle approaching from the right or left at the rear of the vehicle is detected, the following will be displayed on the audio system screen.

WARNING

Cautions regarding the use of the system The driver is solely responsible for safe driving. Always drive safely, taking care to observe your surroundings. The RCTA function is only an assist and is not a replacement for careful driving. Driver must be careful when backing up, even when using RCTA function. The driver’s own visual confirmation of behind you and your vehicle is necessary and be sure there are no pedestrians, other vehicles, etc., before backing up. Failure to do so could cause death or serious injury. According to conditions, the system may not function correctly. Therefore the driver’s own visual confirmation of safety is necessary.

RCTA function detection areas

The areas that vehicles can be detected in are outlined below.

Approaching vehicle	Speed	1 Approximate alert distance
Fast	18 mph (28 km/h)	65 ft. (20 m)
Slow	5 mph (8 km/h)	18 ft. (5.5 m)

The RCTA function is operational when

The RCTA function is turned on.
The shift lever is in R.
Vehicle speed is approximately 5 mph (8 km/h) or less.
Approaching vehicle speed is between approximately 5 mph (8 km/h) and 18 mph (28 km/h).

Conditions under which the RCTA function will not detect a vehicle

The RCTA function is not designed to detect the following types of vehicles and/or objects:

Small motorcycles, bicycles, pedestrians, etc.*
Vehicles approaching from directly behind
Vehicles that the sensors cannot detect due to obstructions
Guardrails, walls, signs, parked vehicles and similar stationary objects*
Vehicles moving away from your vehicle
Vehicles approaching from the parking spaces next to your vehicle*
Vehicles backing up in the parking space next to your vehicle*

Depending on the conditions, detection of a vehicle and/or object may occur.

Conditions under which the RCTA function may not function correctly

The RCTA function may not detect vehicles correctly in the following conditions:
- When the sensor is misaligned due to a strong impact to the sensor or its surrounding area
- When mud, snow, ice, a sticker, etc., is covering the sensor or surrounding area on the rear bumper
- During bad weather such as heavy rain, fog, snow, etc.
- When multiple vehicles approach continuously
- Shallow angle parking
- When a vehicle is approaching at high speed
- When parking on a steep incline, such as hills, a dip in the road, etc.
- Immediately after the RCTA function is turned on
- Immediately after the engine is started with the RCTA function on.

Vehicles that the sensors cannot detect due to obstructions

When items such as a bicycle carrier are installed on the rear of the vehicle

Instances of the RCTA function unnecessarily detecting a vehicle and/or object may increase in the following situations:

When a vehicle passes by the side of your vehicle
When the parking space faces a street and vehicles are being driven on the street
When the distance between your vehicle and metal objects, such as a guardrail, wall, sign, or parked vehicle, which may reflect electrical waves toward the rear of the vehicle, is short
When there are spinning objects near your vehicle such as the fan of an air conditioning unit

Customization
Some functions can be customized.

Rear Camera Detection function (vehicles with panoramic view monitor)

When the vehicle is backing up, the rear camera detection function can detect pedestrians in the detection area behind the vehicle. If a pedestrian is detected, a buzzer will sound and an icon on the audio system screen will be displayed to inform the driver of the pedestrian

Display

Pedestrian detection icon
- Displayed automatically when a pedestrian is detected.
Mute switch
- Select to mute the buzzer. The buzzer will be re-enabled when the shift lever is shifted to a position other than R.

When a pedestrian is detected

If the rear camera detection function detects a pedestrian in the detection area, the buzzer and icon will operate as shown in the following table:

Area	Buzzer	Icon
1	Sounds repeatedly	Blinks 3 times and then stays on
2	When the vehicle is stationary: Sounds 3 times When the vehicle is backing up: Sounds repeatedly	Blinks 3 times and then stays on
3	When it is determined that a pedestrian will enter area 1 within a few seconds: Sounds repeatedly	When it is determined that a pedestrian will enter area 1 within a few seconds: Blinks 3 times and then stays on

The rear camera detection function is operational when
The rear camera detection function is operational when the following conditions are met:

The engine switch is in the IGNITION ON mode.
The shift lever is in R.

Setting the buzzer volume
The buzzer volume of this function changes with the RCTA buzzer volume.

If the rear camera detection function is malfunctioning
If a malfunction of the rear camera detection function is detected, one of the following messages will be displayed on the audio system screen. Have the vehicle inspected by your Toyota dealer.

- “RCD malfunction.”
- “Visit your dealer.”
- “RCD unavailable.”

If “Clean dirt from lens” is displayed on the audio system screen

A rear camera lens may be dirty or covered with snow or ice. In such cases, if it is removed from the rear camera lens, the system should return to normal. (It may be necessary to drive the vehicle for some time before the system returns to normal.)

If “RCD unavailable” is displayed on the audio system screen

If this message is displayed after the battery has been disconnected and reconnected, fully turn the steering wheel to the left and then the right on level ground.
If this message is displayed only when the R shift position is selected, the rear camera lens may be dirty. Clean the rear camera lens.

Situations in which the system may not operate properly

Some pedestrians, such as the following, may not be detected by the rear camera detection function, preventing the function from operating properly:
- Pedestrians who are squatting
- Pedestrians who are lying down
- Pedestrians who are running
- Pedestrians who suddenly enter the detection area
- Pedestrians riding a bicycle, skateboard, or other light vehicle
- Pedestrians wearing unusual clothing, such as a costume
- Pedestrians whose body is partially hidden by a cart or other object
- Pedestrians which are obscured by darkness, such as at night

In some situations, such as the following, pedestrians may not be detected by the rear camera detection function, preventing the function from operating properly:

When backing up in inclement weather (rain, snow, fog, etc.)
When the rear camera is obscured (dirt, snow, ice, etc. are attached) or scratched
When a very bright light, such as the sun, or the headlights of another vehicle, shines directly into the rear camera
When backing up in a place where the surrounding brightness changes suddenly, such as at the entrance or exit of a garage or underground parking lot

In some situations, such as the following, the rear camera detection function may operate even though there are no pedestrians in the detection area.

When a three dimensional object, such as a pole, traffic cone, fence, or parked vehicle, is detected
When a moving object, such as a car or motorcycle is detected
When backing up toward moving objects such as flags or puddles, or airborne matter, such as smoke, steam, rain, or snow
When there is a pattern on the road, due to the road being made of cobblestone or gravel or having tram rails, traces of repair, white lines, pedestrian crossings or fallen leaves on the surface
When backing up on a metal cover (grating), such as those used for drainage ditches
When backing up toward the roadside or a bump in the road
When an object is reflected in a puddle or on a wet road surface
When there are shadows on the road
When backing up over a bump in the road
If the vehicle is significantly tilted, such as when carrying a heavy load
When backing up toward an incline/decline
If the suspension has been modified or tires of a size other than specified are installed
If the rear of the vehicle is raised or lowered due to the carried load
If an electronic component, such as a backlit license plate or rear fog light, is installed near the rear camera
If a bumper protector, such as an additional trim strip, is installed to the rear bumper
If the orientation of the rear camera has been changed due to a collision or other impact, or removal and installation
If a towing eyelet is installed to the rear of the vehicle
When the rear camera is obscured (dirt, snow, ice, etc. are attached) or scratched
When water is flowing over the rear camera lens
If there is a flashing light in the detection area, such as the emergency flashers of another vehicle
Situations in which the rear camera detection function may be difficult to notice
If buzzer may be difficult to hear if the surrounding area is noisy, the volume of the audio system volume is high, the air conditioning system is being used, etc.
If the temperature in the cabin is extremely high or low, the audio system screen may not operate correctly.

Intuitive parking assist

The distance from your vehicle to nearby objects when parallel parking or maneuvering into a garage is measured by the sensors and communicated via the displays and a buzzer. Always check the surrounding area when using this system.

Types of sensors

Front corner sensors
Front center sensors
Rear corner sensors
Rear center sensors

Turning the intuitive parking assist on/off

Press of the meter control switches, select .
Press

of the meter control switches, select
Press of the meter control switch.
Each time

is pressed, the function changes on/off.

Display

When the sensors detect an object, the following displays inform the driver of the position and distance to the object.

Multi-information display

Front corner sensor operation
Front center sensor operation
Rear corner sensor operation
Rear center sensor operation
Select to mute the buzzer sounds.

Audio system screen

Intuitive parking assist
When the vehicle is moving backward.
A simplified image is displayed on the upper part of the screen when an object is detected.

Muting the buzzer sound

To mute the buzzer sound
- The buzzer can be temporarily muted by pressing of the meter control switches while an object detection display is shown on the multi-information display.
To cancel the mute
- Mute will be automatically cancelled in the following situations.
  - When the shift position is changed
  - When the vehicle speed has reached or exceeded approximately 6 mph (10 km/h) with the shift lever in D
  - When the intuitive parking assist is turned off once and turned on again
  - When the engine switch is turned off once and turned to IGNITION ON mode again
  - When a sensor is malfunctioning

Sensor detection display, object distance

Distance display
Sensors that detect an object will illuminate continuously or blink.

Buzzer operation and distance to an object

A buzzer sounds when the sensors are operating.

The buzzer sounds faster as the vehicle approaches an object. When the vehicle comes within the following distance of the object, the buzzer sounds continuously: Approximately 1.2 ft. (35 cm).
When 2 or more objects are detected simultaneously, the buzzer system responds to the nearest object. If one or both come within the above distances, the beep will repeat a long tone, followed by fast beeps.

Detection range of the sensors

Approximately 3.3 ft. (100 cm)
Approximately 4.9 ft. (150 cm)
Approximately 2.6 ft. (80 cm)

The diagram shows the detection range of the sensors. Note that the sensors cannot detect objects that are extremely close to the vehicle. The range of the sensors may change depending on the shape of the object, etc.

The intuitive parking assist can be operated when

Front corner sensors:

The engine switch is in IGNITION ON mode.
The shift lever is in other than P.
The vehicle speed is less than about 6 mph (10 km/h).

Front center sensors:

The engine switch is in IGNITION ON mode.
The shift lever is in other than P or R.
The vehicle speed is less than about 6 mph (10 km/h).

Rear corner and rear center sensors:

The engine switch is in IGNITION ON mode.
The shift lever is in R.
The vehicle speed is less than about 6 mph (10 km/h).

Intuitive parking assist display

When an object is detected while the Toyota parking assist monitor or panoramic view monitor is in use, the warning indicator will appear in the upper part of the screen even if the display setting has been set to off.

Sensor detection information

The sensor’s detection areas are limited to the areas around the vehicle’s bumper.
Depending on the shape of the object and other factors, the detection distance may shorten, or detection may be impossible.
Objects may not be detected if they are too close to the sensor.
There will be a short delay between object detection and display. Even at slow speeds, there is a possibility that the object will come within the sensor’s detection areas before the display is shown and the buzzer sounds.
Thin posts or objects lower than the sensor may not be detected when approached, even if they have been detected once.
It might be difficult to hear beeps due to the volume of audio system or air flow noise of the air conditioning system.

If a battery terminal has been disconnected and reconnected

The system needs to be initialized. To initialize the system, drive the vehicle straight ahead for 5 seconds or more at a speed of approximately 22 mph (35 km/h) or more.

If “Parking Assist Unavailable Clean Parking Assist Sensor” is displayed on the multi-information display

A sensor may be dirty or covered with snow or ice. In such cases, if it is removed from the sensor, the system should return to normal. Also, due to the sensor being frozen at low temperatures, a malfunction display may appear or an object may not be detected. If the sensor thaws out, the system should return to normal.
If “Parking Assist Unavailable” is displayed on the multi-information display
Water may be continuously flowing over the sensor surface, such a s i n a heavy rain. When the system determines that it is normal, the system will return to normal.
Initialization may not have been performed after a battery terminal was disconnected and reconnected. Initialize the system. If this message continues to be displayed even after initialization, have the vehicle inspected by your Toyota dealer.

Certification

For vehicles sold in Canada
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB-001 du Canada.

Customization

Some functions can be customized.

WARNING

When using the intuitive parking assist
Observe the following precautions.
Failing to do so may result in the vehicle being unable to be driven safely and possibly cause an accident.
Do not use the sensor at speeds in excess of 6 mph (10 km/h).
The sensors’ detection areas and reaction times are limited. When moving forward or reversing, check the areas surrounding the vehicle (especially the sides of the vehicle) for safety, and drive slowly, using the brake to control the vehicle’s speed.
Do not install accessories within the sensors’ detection areas.

WARNING

Sensors

Certain vehicle conditions and the surrounding environment may affect the ability of a sensor to correctly detect an object. Particular instances where this may occur are listed below.
There is dirt, snow or ice on the sensor. (Wiping the sensors will resolve this problem.)
The sensor is frozen. (Thawing the area will resolve this problem.) In especially cold weather, if a sensor is frozen the screen may show an abnormal display, or objects may not be detected.
The sensor is covered in any way.
The vehicle is leaning considerably to one side.
On an extremely bumpy road, on an incline, on gravel, or on grass.
The vicinity of the vehicle is noisy due to vehicle horns, motorcycle engines, air brakes of large vehicles, or other loud noises producing ultrasonic waves.
There is another vehicle equipped with parking assist sensors in the vicinity.
The sensor is coated with a sheet of spray or heavy rain.
The sensor is drenched with water on a flooded road.
The vehicle is equipped with a fender pole or wireless antenna.
Towing eyelets are installed.
The bumper or sensor receives a strong impact.
The vehicle is approaching a tall or curved curb
The detection range is reduced due to an object such as a sign.
In harsh sunlight or intense cold weather.
The area directly under the bumpers is not detected.
If objects draw too close to the sensor.
A non-genuine Toyota suspension (lowered suspension, etc.) is installed.
A backlit license plate is installed. In addition to the examples above, there are instances in which, because of their shape, signs and other objects may be judged by a sensor to be closer than they are.

WARNING

Objects which may not be properly detected
The shape of the object may prevent a sensor from detecting it. Pay particular attention to the following objects:
Wires, fences, ropes, etc.
Cotton, snow and other materials that absorb sound waves
Sharply-angled objects
Low objects
Tall objects with upper sections projecting outwards in the direction of your vehicle
People may not be detected if they are wearing certain types of clothing.
Moving objects such as people or animals

NOTICE

When using intuitive parking assist
In the following situations, the system may not function correctly due to a sensor malfunction, etc. Have the vehicle checked by your Toyota dealer.
The intuitive parking assist operation display flashes, and a buzzer sounds when no objects are detected.
If the area around a sensor collides with something, or is subjected to strong impact.
If the bumper collides with something.
If the display shows continuously without beeping, except when the buzzer volume is muted.
If a display error occurs, first check the sensor.
If the error occurs even if there is no ice, snow or mud on the sensor, it is likely that the sensor is malfunctioning.
Notes when washing the vehicle
Do not apply intensive bursts of water or steam to the sensor area.
Doing so may result in the sensor malfunctioning.

Intelligent Clearance Sonar (ICS)

If a collision with an object may occur due to the vehicle suddenly moving forward due to an accidental accelerator pedal operation, the vehicle moving the unintended direction due to the wrong shift position being selected, or while parking or traveling at low speeds, the sensors detect objects, such as a wall, in the traveling direction of the vehicle, and the system operates to lessen an impact with an object and reduce the resulting damage

Examples of system operation

The system will operate in situations such as the following if an object is detected in the traveling direction of the vehicle.

When traveling at a low speed and the brake pedal is not depressed, or is depressed late

When the accelerator pedal is depressed excessively

When the vehicle moves in the unintended direction due to the wrong shift position being selected

Rear Cross Traffic Auto Brake function

If a radar sensor detects a vehicle approaching from the right or left at the rear of the vehicle and a collision may occur, this function will perform brake control to reduce the likelihood of an impact with the approaching vehicle.

Examples of system operation
The system will operate in situations such as the following if an object is detected in the traveling direction of the vehicle.

When reversing, a vehicle is approaching and the brake pedal is not depressed, or is depressed late

Types of sensors

Front corner sensors
Front center sensors
Rear corner sensors
Rear center sensors

Turning the Intelligent Clearance Sonar system on/off

Press of the meter control switches, select

.
Press of the meter control switches, select
Press

of the meter control switch.
Select the “Yes” and push .

When the Intelligent Clearance Sonar is disabled, the ICS OFF indicator illuminates.
To re-enable the system when it was disabled, select on the multi-informationdisplay, select and then “On”. If disabled using this method, the system will not be re-enabled by turning the engine switch off and then to IGNITION ON mode

Displays and buzzers for engine output restriction control and brake control

If the engine output restriction control or brake control operates, a buzzer will sound and a message will be displayed on the multi-information display to alert the driver. Depending on the situation, engine output restriction control will operate to either limit acceleration or restrict output as much as possible

Control	Situation	Multi-information display	ICS OFF Indicator	Buzzer
Engine output restriction con- trol is operating (acceleration restriction)	Acceleration greater than a certain amount is not possible.	“Object Detected Acceleration Reduced”	Not illu- minated	¾
Engine output restriction con- trol is operating (output restricted as much as pos- sible)	Stronger-than- normal brake operation is nec- essary.	“Brake!”		Short beep
Brake control is operating	Emergency brak- ing is necessary.	“Brake!”
Vehicle stopped by system opera- tion	The vehicle has been stopped by brake control operation.	If the accelera- tor pedal is depressed: “Switch to Brake” If the accelera- tor pedal is not depressed: “Brake”	Illumi- nated

Intelligent Clearance Sonar function

If the Intelligent Clearance Sonar function detects that a collision with an object is possible, the engine output will be restricted to restrain any increase in the vehicle speed. (Engine output restriction control: See A below.) Additionally, if the accelerator pedal continues to be depressed, the brakes will be applied automatically to reduce the vehicle speed. (Brake control: See B below.)

Accelerator pedal
Brake pedal
Engine output
Braking force
Start of control
High possibility of a collision
Extremely high possibility of a collision

The Intelligent Clearance Sonar function will operate when
The function will operate when the ICS OFF indicator is not illuminated or flashing and all of the following conditions are met:

Engine output restriction control

The Intelligent Clearance Sonar system is enabled.
The vehicle speed is 10 mph (15 km/h) or less.
There is an object in the traveling direction of the vehicle and 6 to 13 ft. (2 to 4 m) away.
The system determines that a stronger-than-normal brake operation is necessary to avoid a collision.
Brake control
Engine output restriction control is operating.
The system determines that an emergency brake operation is necessary to avoid a collision.

The Intelligent Clearance Sonar function will stop operating when

The function will stop operating if any of the following conditions are met:

Engine output restriction control

The Intelligent Clearance Sonar system is disabled.
The collision becomes avoidable with normal brake operation.
The object is no longer 6 to 13 ft. (2 to 4 m) away in the traveling direction of the vehicle.

Brake control

The Intelligent Clearance Sonar system is disabled.
Approximately 2 seconds elapse after the vehicle is stopped by brake control.
The brake pedal is depressed after the vehicle is stopped by brake control.
The object is no longer 6 to 13 ft. (2 to 4 m) away in the traveling direction of the vehicle.

Detection range of the Intelligent Clearance Sonar function

The detection range of the Intelligent Clearance Sonar function differs from the detection range of the intuitive parking assist.
Therefore, even if the intuitive parking assist detects an object and provides a warning, the Intelligent Clearance Sonar function may not start operating.

If the Intelligent Clearance Sonar function has operated

If the vehicle is stopped due to operation of the Intelligent Clearance Sonar function, the Intelligent Clearance Sonar system will be disabled and the ICS OFF indicator will illuminate.

Re-enabling the Intelligent Clearance Sonar system

To re-enable the Intelligent Clearance Sonar system when it is disabled due to operation of the Intelligent Clearance Sonar function, either enable the system again, or turn the engine switch off and then back to IGNITION ON mode. Additionally, if the object becomes no longer in the traveling direction of the vehicle or if the traveling direction of the vehicle changes (such as changing from moving forward to backing up, or from backing up to moving forward), the system will be re-enabled automatically.

Objects that the Intelligent Clearance Sonar function may not detect
The sensors may not be able to detect certain objects, such as the following.

Cotton cloth, snow, and other materials that are poor reflectors of ultrasonic waves.
(People may also not be detected depending on the type of clothing they are wearing.)

Objects which are not perpendicular to the ground, are not perpendicular to the traveling direction of the vehicle, are uneven or are waving.

Low objects
Thin objects such as wires, fences, ropes and signposts
Objects that are extremely close to the bumper

Situations in which the Intelligent Clearance Sonar may not operate properly
When the shift lever is in N

Intuitive parking assist buzzer
Regardless of whether the intuitive parking assist system is enabled or not if the Intelligent Clearance Sonar system is enabled, the front or rear sensors detect an object and brake control is performed, the intuitive parking assist buzzer will sound to notify the driver of the approximate distance to the object.

Situations in which the Intelligent Clearance Sonar function may operate even if there is no possibility of a collision

In some situations such as the following, the Intelligent Clearance Sonar function may operate even though there is no possibility of a collision.

Vehicle surroundings

When driving on a narrow road
When driving on a gravel road or in an area with tall grassWhen driving on a narrow road
When driving on a gravel road or in an area with tall grass
When driving toward a banner, flag, low-hanging branch or boom barrier (such as those used at railroad crossings, toll gates and parking lots).
When driving on a narrow path surrounded by a structure, such as in a tunnel or on an iron bridge
When parallel parking
When there is a rut or hole in the surface of the road
When driving on a metal cover (grating), such as those used for drainage ditches
When driving on a steep slope
If a sensor is hit by a large amount of water, such as when driving on a flooded road

Weather

If a sensor is covered with ice, snow, dirt, etc. (when cleared, the system will return to normal)
If heavy rain or water strikes a sensor
When driving in inclement weather such as fog, snow or a sandstorm

Other ultrasonic waves sources

When vehicle horns, vehicle detectors, motorcycle engines, air brakes of large vehicles, the clearance sonar of other vehicles or other devices which produce ultrasonic waves are near the vehicle
If a sticker or an electronic component, such as a backlit license plate (especially fluorescent type), fog lights, a fender pole or wireless antenna is installed near a sensor

Changes in the vehicle posture

If the vehicle is significantly tilted
If the front of the vehicle is raised or lowered due to the carried load
If the orientation of a sensor has been changed due to a collision or other impact

If the Intelligent Clearance Sonar function operates unnecessarily such as at a railroad crossing

Even in the event that the Intelligent Clearance Sonar function operates unnecessarily, such as at a railroad crossing, brake control will be canceled after approximately 2 seconds, allowing you to proceed forward and leave the area, Brake control can also be canceled by depressing the brake pedal. Depressing the accelerator pedal again will allow you to proceed forward and leave the area.

Situations in which the Intelligent Clearance Sonar Brake function may not operate properly

In some situations such as the following, this function may not operate properly. Weather

When a sensor or the area around a sensor is extremely hot or cold
When strong winds are blowing

If a sensor is covered with ice, snow, dirt, etc. (when cleared, the system will return to normal)

If heavy rain or water strikes a sensor
When driving in inclement weather such as fog, snow or a sandstorm

Vehicle surroundings

When an object that cannot be detected is between the vehicle and a detected object
If an object such as a vehicle, motorcycle, bicycle or pedestrian cuts in front of the vehicle or runs out from the side of the vehicle. Other ultrasonic waves sources
When vehicle horns, vehicle detectors, motorcycle engines, air brakes of large vehicles, the clearance sonar of other vehicles or other devices which produce ultrasonic waves are near the vehicle
If a sticker or an electronic component, such as a backlit license plate (especially fluorescent type), fog lights, a fender pole or wireless antenna is installed near a sensor

Changes in the vehicle posture

If the vehicle is significantly tilted
If the front of the vehicle is raised or lowered due to the carried load
If the orientation of a sensor has been changed due to a collision or other impact

If a battery terminal has been disconnected and reconnected
The system needs to be initialized. To initialize the system, drive the vehicle straight ahead for 5 seconds or more at a speed of approximately 22 mph (35 km/h) or more.

If “ICS Unavailable” is displayed on the multi-information display and the ICS OFF indicator is flashing

Initialization may not have been performed after a battery terminal was disconnected and reconnected. Initialize the system. If this message continues to be displayed even after initialization, have the vehicle inspected by your Toyota dealer.

If “ICS Unavailable” and “Parking Assist Unavailable Clean Parking Assist Sensor” are displayed on the multi-information display and the ICS OFF indicator is flashing

A sensor may be covered with ice, snow, dirt, etc. In this case, remove the ice, snow, dirt, etc., from the sensor to return the system to normal. If this message is shown even after removing dirt from the sensor, or shown when the sensor was not dirty to begin with, have the vehicle inspected at your Toyota dealer.
A sensor may be frozen. Once the ice melts, the system will return to normal.
Water may be continuously flowing over the sensor surface, such as in a heavy rain. When the system determines that it is normal, the system will return to normal.

WARNING

Limitations of the Intelligent Clearance Sonar systemDo not overly rely on the system, as doing so may lead to an accident.
The driver is solely responsible for safe driving. Always drive carefully, taking care to observe your surroundings. The Intelligent Clearance Sonar system is designed to provide support to lessen the severity of collisions.
However, it may not operate in some situations.
The Intelligent Clearance Sonar system is not designed to stop the vehicle completely. Additionally, even if the system has stopped the vehicle, it is necessary to depress the brake pedal immediately as brake control will be canceled after approximately 2 seconds.
To ensure the Intelligent Clearance Sonar system can operate properly
Observe the following precautions regarding the sensors. Failure to do so may cause a sensor to not operate properly, and may cause an accident.
Do not modify, disassemble or paint the sensors.
Do not replace a sensor with a part other than a genuine part.
Do not subject a sensor or its surrounding area to a strong impact.
Do not damage the sensors, and always keep them clean.
Observe the following precautions regarding the radar sensors
Failure to do so may cause a radar sensor to not operate properly, and may cause an accident.
Do not modify, disassemble or paint the sensors.
Do not replace a radar sensor with a part other than a genuine part.
Do not subject a radar sensor or its surrounding area to a strong impact.
Do not damage the radar sensors, and always keep the radar sensors and their surrounding area on the bumper clean.
Handling the suspension
Do not modify the suspension, as changes to the height or inclination of the vehicle may prevent the sensors from detecting objects correctly or cause the system to not operate or operate unnecessarily.

NOTICE

To prevent the system from malfunctioning
If the area around a sensor is subjected to an impact, the system may not operate properly due to the sensor being misaligned. Have the vehicle inspected by your Toyota dealer.
When using a high pressure washer to wash the vehicle, do not spray the sensors directly, as doing so may cause a sensor to malfunction.
When using steam to clean the vehicle, do not direct steam too close to the sensors as doing so may cause a sensor to malfunction.
To prevent a radar sensor from malfunctioning
If the area around a radar sensor is subjected to an impact, the system may not operate properly due to a sensor malfunction. Have the vehicle inspected by your Toyota dealer.
Observe the radar sensor handling precautions.
To prevent unnecessary operation of the Intelligent Clearance Sonar system
In the following situations, disable the Intelligent Clearance Sonar system as the system may operate even though there is no possibility of a collision.
When inspecting the vehicle using a chassis roller, chassis dynamo or free roller
When loading the vehicle onto a boat, truck or other transport vessel
If the suspension has been modified or tires of a size other than specified are installed
If the front of the vehicle is raised or lowered due to the carried load
When equipment that may obstruct a sensor is installed, such as a towing eyelet, bumper protector (an additional trim strip, etc.), bicycle carrier, or snow plow
When using an automatic car wash

Rear Cross Traffic Auto Brake function

If the Rear Cross Traffic Auto Brake function detects that a collision with an approaching vehicle is possible, the engine output will be restricted to restrain any increase in vehicle speed. (Engine output restriction control: See A below.) Additionally, if the accelerator pedal continues to be depressed, the brakes will be applied automatically to reduce the vehicle speed. (Brake control: See B below.).

Accelerator pedal
Brake pedal
Engine output
Braking force
Start of control
High possibility of a collision
Extremely high possibility of a collision

The Rear Cross Traffic Auto Brake function will operate when
The function will operate when the ICS OFF indicator is not illuminated or flashing and all of the following conditions are met:

Engine output restriction control

The Intelligent Clearance Sonar with Rear Cross Traffic Auto Brake is enabled.
The vehicle speed is 10 mph (15 km/h) or less.
Vehicles which are approaching from the right or left at the rear of the vehicle at a traveling speed of approximately 5 mph (8 km/h) or more.
The shift lever is in R.
The system determines that a stronger than normal brake operation is necessary to avoid a collision with an approaching vehicle.

Brake control

Engine output restriction control is operating.
The system determines that an emergency brake operation is necessary to avoid a collision with an approaching vehicle.

The Rear Cross Traffic Auto Brake function will stop operating when

The function will stop operating if any of the following conditions are met:

Engine output restriction control

The Intelligent Clearance Sonar with Rear Cross Traffic Auto Brake is disabled.
The collision becomes avoidable with normal brake operation.
A vehicle is no longer approaching from the right or left at the rear of the vehicle.

Brake control

The Intelligent Clearance Sonar with Rear Cross Traffic Auto Brake is disabled.
Approximately 2 seconds elapse after the vehicle is stopped by brake control.
The brake pedal is depressed after the vehicle is stopped by brake control.
A vehicle is no longer approaching from the right or left at the rear of the vehicle.

Detection area of the Rear Cross Traffic Auto Brake function
The detection area of the Rear Cross Traffic Auto Brake function differs from the detection area of the RCTA function Therefore, even if the RCTA function detects a vehicle and provides an alert, the Rear Cross Traffic Auto Brake function may not start operating.

If the Rear Cross Traffic Auto Brake function has operated

If the vehicle is stopped due to operation of the Rear Cross Traffic Auto Brake function, the Rear Cross Traffic Auto Brake function will be disabled and the ICS OFF indicator will illuminate.

Re-enabling the Rear Cross Traffic Auto Brake function
To re-enable the Rear Cross Traffic Auto Brake function when it is disabled while it is operating, either enable the Intelligent Clearance Sonar system again, or turn the engine switch off and then back to IGNITION ON mode. When the function is disabled, the ICS OFF indicator will illuminate.
If there is no longer a vehicle approaching from the right or left at the rear of the vehicle when backing up, or if the traveling direction of the vehicle changes (such as changing from backing up to moving forward), the system will be re-enabled automatically. When the function is re-enabled, the ICS OFF indicator will turn off.

Conditions under which the Rear Cross Traffic Auto Brake function will not detect a vehicle
The Rear Cross Traffic Auto Brake function is not designed to detect the following types of vehicles and/or objects.

Vehicles approaching from directly behind
Vehicles backing up in a parking space next to your vehicle
Vehicles that the sensors cannot detect due to obstructions
Vehicles which suddenly accelerate or decelerate near your vehicle
Guardrails, walls, signs, parked vehicles and similar stationary objects*
Small motorcycles, bicycles, pedestrians, etc.*
Vehicles moving away from your vehicle
Vehicles approaching from the parking spaces next to your vehicle*
Depending on the conditions, detection of a vehicle and/or object may occur.

RCTA function buzzer
Regardless of whether the RCTA function is enabled or not, if the Rear Cross Traffic Auto Brake function is enabled and brake control is performed, a buzzer will sound to notify the driver.

Situations in which the system may operate even though there is no possibility of a collision

In some situations such as the following, the Rear Cross Traffic Auto Brake function may operate even though there is no possibility of a collision.
When the parking space faces a street and vehicles are being driven on the street
When a detected vehicle turns while approaching the vehicle
When a vehicle passes by the side of your vehicle
When the distance between your vehicle and metal objects, such as a guardrail, wall, sign, or parked vehicle, which may reflect electrical waves toward the rear of the vehicle, is short
When there are spinning objects near your vehicle such as the fan of an air conditioning unit
When water is splashed or sprayed toward the rear bumper, such as from a sprinkler

Situations in which the Rear Cross Traffic Auto Brake function may not operate properly

In some situations such as the following, this function may not operate properly.

Objects and vehicles which the radar sensors are not designed to detect

Stationary objects
Vehicles which are moving away from your vehicle
Pedestrians, motorcycles, bicycles, etc.*
Objects which are extremely close to a radar sensor
Vehicles which are approaching from the right or left at the rear of the vehicle at a traveling speed of less than approximately 5 mph (8 km/h)
Vehicles which are approaching from the right or left at the rear of the vehicle at a traveling speed of more than approximately 15 mph (24 km/h)
Depending on conditions, detection of a vehicle and/or object may occur.

Situations in which the radar sensors may not be able to detect an object

When a sensor or the area around a sensor is extremely hot or cold
If the rear bumper is covered with ice, snow, dirt, etc.
If heavy rain or water strikes the vehicle
When the detection area of a radar sensor is obstructed by an adjacent vehicle
If the vehicle is significantly tilted
When equipment that may obstruct a sensor is installed, such as a towing eyelet, bumper protector (an additional trim strip, etc.), bicycle carrier, or snow plow
If the suspension has been modified or tires of a size other than specified are installed
If the front of the vehicle is raised or lowered due to the carried load
If a sticker or an electronic component, such as a backlit license plate (especially fluorescent type), fog lights, a fender pole or wireless antenna is installed near a radar sensor
If the orientation of a radar sensor has been changed due to a collision or other impact or removal and installation
When multiple vehicles are approaching with only a small gap between each vehicle
When a vehicle is approaching at high speed

Situations in which the radar sensor may not detect a vehicle

When a vehicle approaches from the right or left at the rear of the vehicle while you are turning while backing up
When turning while backing up
When backing out of a shallow angle parking spot
Vehicles that the sensors cannot detect due to obstructions
When backing up on a slope with a sharp change in grade
When a vehicle turns into the detection area

Handling the radar sensors

Driving mode select switches

The driving modes can be selected to suit driving condition.

Vehicles without AVS (Adaptive Variable Suspension System)

Normal mode
Use for normal driving. While in Eco drive mode or Sport mode, press the “NORMAL” switch to change the driving mode to normal mode.

Eco drive mode
Use Eco drive mode to help achieve low fuel consumption during trips that involve frequent accelerating. When the “ECO” switch is pressed, the “ECO MODE” indicator comes on in the multi-information display.

Sport mode
Use sport mode when increased acceleration response and precise handling is desired, for example, when driving on mountain roads.When the “SPORT” switch is pressed, the “SPORT” indicator comes on in the multi-information display.

Vehicles with AVS (Adaptive Variable Suspension System)

Normal mode/Custom mode

Normal mode

Use for normal driving.
While in Eco drive mode, Sport mode or Custom mode press the “NORMAL/
CUSTOM” switch to change the driving mode to normal mode.

Custom mode

Allows you to drive with the following functions set to your preferred settings.
Custom mode settings can only be changed on the drive mode customization display of the audio system screen.
(Displaying the drive mode customization display:
When the “NORMAL/CUSTOM” switch is pressed, the “CUSTOM” indicator comes on in the multi-information display.

Function	Setting
Powertrain	Normal
	Power
	Eco
Chassis	Normal
Chassis	Sport
Air conditioning system	Normal
Air conditioning system	Eco

Operation of the air conditioning system in Eco drive mode
Eco drive mode controls the heating/cooling operations and fan speed of the air conditioning system to enhance fuel efficiency . To improve air conditioning performance, adjust the fan speed or turn off Eco drive mode.

Automatic deactivation of sport mode and custom mode
If the engine switch is turned off after driving in sport mode or custom mode, the drive mode will be changed to normal mode

Driving assist systems

To keep driving safety and performance, the following systems operate automatically in response to various driving situations. Be aware, however, that these systems are supplementary and should not be relied upon too heavily when operating the vehicle.

ABS (Anti-lock Brake System)
Helps to prevent wheel lock when the brakes are applied suddenly, or if the brakes are applied while driving on a slippery road surface

Brake assist
Generates an increased level of braking force after the brake pedal is depressed when the system detects a panic stop situation

VSC (Vehicle Stability Control)
Helps the driver to control skidding when swerving suddenly or turning on slippery road surfaces.

Enhanced VSC (Enhanced Vehicle Stability Control)
Provides cooperative control of the ABS, TRAC, VSC and EPS. Helps to maintain directional stability when swerving on slippery road surfaces by controlling steering performance.

TRAC (Traction Control)
Helps to maintain drive power and prevent the drive wheels from spinning when starting the vehicle or accelerating on slippery roads

Active Cornering Assist (ACA) (if equipped)
Helps to prevent the vehicle from sliding to the outer side by performing inner wheel brake control when attempting to accelerate while turning

Hill-start assist control
Helps to reduce the backward movement of the vehicle when starting on an uphill

EPS (Electric Power Steering)
Employs an electric motor to reduce the amount of effort needed to turn the steering wheel

Adaptive Variable Suspension System (if equipped)
By independently controlling the damping force of the shock absorbers for each of the 4 wheels according to the road and driving conditions, this system helps riding comfort with superior vehicle stability, and helps good vehicle posture

The Secondary Collision Brake
When the SRS airbag sensor detects a collision and the system operates, the brakes and stop lights are automatically controlled to reduce the vehicle speed and help reduce the possibility of further damage due to a secondary collision.

Dynamic Torque Control AWD system (if equipped)
Automatically switches from front-wheel drive to all-wheel drive (AWD) according to the driving conditions, helping to ensure reliable handling and stability. Examples of conditions where the system will switch to AWD are when cornering, going uphill, starting off or accelerating, and when the road surface is slippery due to snow, rain, etc.

When the TRAC/VSC systems are operating

The slip indicator light will flash while the TRAC/VSC systems are operating.

Disabling the TRAC system

If the vehicle gets stuck in mud, dirt or snow, the TRAC system may reduce power from the engine to the wheels. Pressing to turn the system off may make it easier for you to rock the vehicle in order to free it. To turn the TRAC system off, quickly press and release . “Traction Control Turned Off” will be shown on the multi-information display. Press again to turn the system back on.

Turning off both TRAC and VSC systems

To turn the TRAC and VSC systems off, press and hold for more than 3 seconds while the vehicle is stopped. The VSC OFF indicator light will come on and the “Traction Control Turned Off” will be shown on the multi-information display*. Press again to turn the system back on. *: Pre-collision brake assist and pre-collision braking will also be disabled. The PCS warning light will come on and the message will be shown on the multi-information display.

When the message is displayed on the multi-information display showing that TRAC has been disabled even if has not been pressed

TRAC is temporary deactivated. If the information continues to show, contact your Toyota dealer.

Operating conditions of hill-start assist control

When the following four conditions are met, the hill-start assist control will operate:

The shift lever is in a position other than P or N (when starting off forward/ backward on an upward incline)
The vehicle is stopped
The accelerator pedal is not depressed
The parking brake is not engaged

Automatic system cancelation of hill-start assist control

The hill-start assist control will turn off in any of the following situations:

The shift lever is shifted to P or N
The accelerator pedal is depressed
The parking brake is engaged
2 seconds at maximum elapsed after the brake pedal is released

Sounds and vibrations caused by the ABS, brake assist, VSC, TRAC and hill-start assist control systems

A sound may be heard from the engine compartment when the brake pedal is depressed repeatedly, when the engine is started or just after the vehicle begins to move. This sound does not indicate that a malfunction has occurred in any of these systems.
Any of the following conditions may occur when the above systems are operating. None of these indicates that a malfunction has occurred.
Vibrations may be felt through the vehicle body and steering.
A motor sound may be heard also after the vehicle comes to a stop.
The brake pedal may pulsate slightly after the ABS is activated.
The brake pedal may move down slightly after the ABS is activated.

EPS operation sound

When the steering wheel is operated, a motor sound (whirring sound) may be heard. This does not indicate a malfunction.

Active Cornering Assist operation sounds and vibrations

When the Active Cornering Assist is operated, operation sounds and vibrations may be generated from the brake system, but this is not a malfunction.

Automatic reactivation of TRAC and VSC systems

After turning the TRAC and VSC systems off, the systems will be automatically re-enabled in the following situations:
When the engine switch is turned off
If only the TRAC system is turned off, the TRAC will turn on when vehicle speed increases If both the TRAC and VSC systems are turned off, automatic re-enabling will not occur when vehicle speed increases.

Operating conditions of Active Cornering Assist

The system operates when the following occurs.
TRAC/VSC can operate
The driver is attempting to accelerate while turning
The system detects that the vehicle is sliding to the outer side
The brake pedal is released

Secondary Collision Brake operating conditions

The system operates when the SRS airbag sensor detects a collision while the vehicle is in motion. However, the system does not operate in any of the following situations.
The vehicle speed is below 6 mph (10 km/h)
Components are damaged

Secondary Collision Brake automatic cancellation

The system is automatically canceled in any of the following situations.
The vehicle speed drops below approximately 6 mph (10 km/h)
A certain amount of time elapses during operation
The accelerator pedal is depressed a large amount
Reduced effectiveness of the EPS system
The effectiveness of the EPS system is reduced to prevent the system from overheating when there is frequent steering input over an extended period of time. The steering wheel may feel heavy as a result.
Should this occur, refrain from excessive steering input or stop the vehicle and turn the engine off. The EPS system should return to normal within 10 minutes.
If a message about AWD is shown on the multi-information display Perform the following actions.

WARNING.

The ABS does not operate effectively when
The limits of tire gripping performance have been exceeded (such as excessively worn tires on a snow covered road).
The vehicle hydroplanes while driving at high speed on wet or slick roads
Stopping distance when the ABS is operating may exceed that of normal conditions The ABS is not designed to shorten the vehicle’s stopping distance. Always maintain a safe distance from the vehicle in front of you, especially in the following situations:
When driving on dirt, gravel or snow-covered roads
When driving with tire chains
When driving over bumps in the road
When driving over roads with potholes or uneven surfaces
TRAC/VSC may not operate effectively when Directional control and power may not be achievable while driving on slippery road surfaces, even if the TRAC/VSC system is operating. Drive the vehicle carefully in conditions where stability and power may be lost.
Active Cornering Assist does not operate effectively when
Do not overly rely on Active Cornering Assist. Active Cornering Assist may not operate effectively when accelerating down slopes or driving on slippery road surfaces.
When Active Cornering Assist frequently operates, Active Cornering Assist may temporarily stop operating to:
• Ensure proper operation of the brakes, TRAC and VSC.
Prevent the brakes from overheating.

WARNING

Hill- start assist control does not operate effectively when
Do not overly rely on hill-start assist control. Hill-start assist control may not operate effectively on steep inclines and roads covered with ice.
Unlike the parking brake, hill-start assist control is not intended to hold the vehicle stationary for an extended period of time. Do not attempt to use hill-start assist control to hold the vehicle on an incline, as doing so may lead to an accident.
When the TRAC/VSC is activated The slip indicator light flashes. Always drive carefully. Reckless driving may cause an accident. Exercise particular care when the indicator light flashes.
When the TRAC/VSC systems are turned off Be especially careful and drive at a speed appropriate to the road conditions. As these are the systems to help ensure vehicle stability and driving force, do not turn the TRAC/VSC systems off unless necessary.
Replacing tires Make sure that all tires are of the specified size, brand, tread pattern and total load capacity. In addition, make sure that the tires are inflated to the recommended tire inflation pressure level. The ABS,
TRAC and VSC systems will not function correctly if different tires are installed on the vehicle. Contact your Toyota dealer for further information when replacing tires or wheels.
Handling of tires and the suspension Using tires with any kind of problem or modifying the suspension will affect the driving assist systems, and may cause a system to malfunction.
Secondary Collision Brake Do not rely solely upon the Secondary Collision Brake. This system is designed to help reduce the possibility of further damage due to a secondary collision, however, that effect changes according to various conditions. Overly relying on the system may result in death or serious injury.

FAQ

What is 2022 Toyota Avalon Safety Sense™ and how does it help the driver?

Toyota Safety Sense™ is a suite of advanced safety features designed to support driver awareness, decision-making, and vehicle operation over a range of speeds and conditions.

How does the Pre-Collision System work in the 2022 Toyota Avalon?

This system uses radar and cameras to detect potential frontal collisions and can alert the driver with visual and audio warnings, and in some situations, can automatically apply the brakes to prevent or mitigate a collision.

What is Lane Tracing Assist (LTA) in the 2022 Toyota Avalon?

LTA assists the driver by recognizing lane markings and preceding vehicles on the road and provides steering input to help the driver stay centered in their lane.

How does the 2022 Toyota Avalon Blind Spot Monitor (BSM) operate?

BSM uses radar sensors to detect vehicles in adjacent lanes that might be in the car’s blind spot, alerting the driver with illuminated indicators on side mirrors.

Useful Links

View Full PDF: 2022 Toyota Avalon Hybrid User Guide | Auto User Guide

2023 Toyota Camry Specs, Price, Features and Mileage (Brochure)

2022 Toyota Avalon Operating The Lights And Wipers User Guide

2022 Toyota Avalon Driving Assist system User Guide

2022 Toyota Avalon Driving Assist system User Guide

Toyota Safety Sense 2.5+

Sensors

PCS (Pre-Collision System)

Detectable objects

System functions

Changing settings of the pre-collision system

LTA (Lane Tracing Assist)

Summary of functions (adsbygoogle = window.adsbygoogle || []).push({});

WARNING

WARNING

Functions included in LTA system

Turning LTA system on

Indications on the multi-information display

RSA (Road Sign Assist)

Summary of function

Indication on the multi-information display

Supported types of road signs

Notification function

Dynamic radar cruise control with full speed range

Summary of functions

System Components

Driving in vehicle-to-vehicle distance control mode

Setting the vehicle speed (vehicle-to-vehicle distance control mode

Adjusting the set speed

Changing the vehicle-to-vehicle distance (vehicle-to-vehicle distance control mode)

Vehicle-to-vehicle distance settings (vehicle-to-vehicle distance control mode

Resuming follow-up cruising when the vehicle has been stopped by system control (vehicle-to-vehicle distance control mode)

Canceling and resuming the speed control

Approach warning (vehicle-to-vehicle distance control mode)

Curve speed reduction function

Selecting constant speed control mode

BSM (Blind Spot Monitor)

Summary of the Blind Spot Monitor

Turning the BSM function/RCTA function on/off

FCC

WARNING

BSM function

BSM function detection areas

WARNING

RCTA function

RCTA function detection areas

Rear Camera Detection function (vehicles with panoramic view monitor)

Display

When a pedestrian is detected

Intuitive parking assist

Types of sensors

Turning the intuitive parking assist on/off

Display

Sensor detection display, object distance

Intelligent Clearance Sonar (ICS)

Examples of system operation

Rear Cross Traffic Auto Brake function

Types of sensors

Turning the Intelligent Clearance Sonar system on/off

Displays and buzzers for engine output restriction control and brake control

Intelligent Clearance Sonar function

WARNING

Rear Cross Traffic Auto Brake function

Driving mode select switches

The driving modes can be selected to suit driving condition.

Driving assist systems

When the TRAC/VSC systems are operating

Disabling the TRAC system

FAQ

Useful Links

Category

About Us

Privacy Policy

Contact Us

Summary of functions