2024 Chrysler Pacifica Warning Lights and Indicator User Guide

2024 Chrysler Pacifica Warning Lights and Indicator User Guide

As car technology is always changing, it’s important to know how to use the different warning and signal lights in cars like the 2024 Chrysler Pacifica so that you can drive safely and efficiently.

2023 – 2024 Chrysler Pacifica Plug-in Hybrid Specs, Price, Features, Mileage and Review

Video: 2024 Chrysler Pacifica Warning Lights

2024 CHRYSLER LIGHTS AND MESSAGES

The warning/indicator lights will illuminate in the instrument panel together with a dedicated message and/or acoustic signal when applicable. These indications are indicative and precautionary and as such must not be considered as exhaustive and/or alternative to the information contained in the Owner’s Manual, which you are advised to read carefully in all cases. Always refer to the information in this chapter in the event of a failure indication. All active telltales will display first if applicable. The system check menu may appear different based on equipment options and current vehicle status. Some telltales are optional and may not appear.

RED WARNING LIGHTS

Air Bag Warning Light This warning light will illuminate to indicate a fault with the airbag and will turn on for four to eight seconds as a bulb check when the ignition is placed in the ON/RUN or ACC/ON/RUN position. This light will illuminate with a single chime when a fault with the airbag has been detected, it will stay on until the fault is cleared. If the light is either not on during startup, stays on, or turns on while driving, have the system inspected at an authorized dealer as soon as possible.

Battery Charge Warning Light This warning light will illuminate when the battery is not charging properly. If it stays on while the engine is running, there may be a malfunction with the charging system. Contact an authorized dealer as soon as possible. This indicates a possible problem with the electrical system or a related component. Brake Warning Light This warning light monitors various brake functions, including brake fluid level and parking brake application. If the brake light turns on it may indicate that the parking brake is applied, that the brake fluid level is low, or that there is a problem with the Anti-Lock Brake System reservoir. If the light remains on when the parking brake has been disengaged, and the fluid level is at the full mark on the master cylinder reservoir, it indicates a possible brake hydraulic system malfunction or that a problem with the Brake Booster has been detected by the Anti-Lock Brake System (ABS) / Electronic Stability Control (ESC) system. In this case, the light will remain on until the condition has been corrected. If the problem is related to the brake booster, the ABS pump will run when applying the brake, and a brake pedal pulsation may be felt during each stop. The dual brake system provides a reserve braking capacity in the event of a failure of a portion of the hydraulic system. A leak in either half of the dual brake system is indicated by the Brake Warning Light, which will turn on when the brake fluid level in the master cylinder has dropped below a specified level. The light will remain on until the cause is corrected. NOTE: The light may flash momentarily during sharp cornering maneuvers, which change fluid level conditions. The vehicle should have service performed, and the brake fluid level checked. If brake failure is indicated, immediate repair is necessary. WARNING! Driving a vehicle with the red brake light on is dangerous. Part of the brake system may have failed. It will take longer to stop the vehicle. You could have a collision. Have the vehicle checked immediately. Vehicles equipped with the Anti-Lock Brake System (ABS) are also equipped with Electronic Brake Force Distribution (EBD). In the event of an EBD failure, the Brake Warning Light will turn on along with the ABS Light. Immediate repair to the ABS is required. Operation of the Brake Warning Light can be checked by turning the ignition switch from the OFF position to the ON/RUN position. The light should illuminate for approximately two seconds. The light should then turn off unless the parking brake is applied or a brake fault is detected. If the light does not illuminate, have the light inspected by an authorized dealer. The light also will turn on when the parking brake is applied with the ignition switch in the ON/RUN position. NOTE: This light shows only that the parking brake is applied. It does not show the degree of brake application. Door Open Warning Light This warning light will illuminate when a door is ajar/open and not fully closed. This indica-tor will reflect which doors are open. NOTE: If the vehicle is moving, there will also be a single chime. Electric Power Steering Fault Warning Light This warning light will turn on when there’s a fault with the Electric Power Steering (EPS) system. WARNING! Continued operation with reduced assist could pose a safety risk to yourself and others. Service should be obtained as soon as possible. Electronic Throttle Control (ETC) Warning Light This warning light will illuminate to indicate a problem with the ETC system. If a problem is detected while the vehicle is running, the light will either stay on or flash depending on the nature of the problem. Cycle the ignition when the vehicle is safely and completely stopped and the transmission is placed in the PARK (P) position. The light should turn off. If the light remains on with the vehicle running, your vehicle will usually be drivable; however, see an authorized dealer for service as soon as possible. NOTE: This light may turn on if the accelerator and brake pedals are pressed at the same time. If the light continues to flash when the vehicle is running, immediate service is required and you may experi-ence reduced performance, an elevated/rough idle, or engine stall and your vehicle may require towing. The light will come on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and remain on briefly as a bulb check. If the light does not come on during starting, have the system checked by an authorized dealer. Engine Coolant Temperature Warning Light This warning light warns of an overheated engine condition. If the engine coolant tem-perature is too high, this indicator will illuminate and a single chime will sound. If the temperature reaches the upper limit, a continuous chime will sound for four minutes or until the engine is able to cool; whichever comes first. If the light turns on while driving, safely pull over and stop the vehicle. If the Air Conditioning (A/C) system is on, turn it off. Also, shift the transmission into NEUTRAL (N) and idle the vehicle. If the temperature reading does not return to normal, turn the engine off immediately and call for service.

Hood Open Warning Light This warning light will illuminate when the hood is left open and not fully closed. NOTE: If the vehicle is moving, there will also be a single chime. Liftgate Open Warning Light This warning light will illuminate when the liftgate is open. NOTE: If the vehicle is moving, there will also be a single chime. Oil Pressure Warning Light This warning light will illuminate to indicate low engine oil pressure. If the light turns on while driving, stop the vehicle, shut off the engine as soon as possible, and contact an authorized dealer. A chime will sound when this light turns on. Do not operate the vehicle until the cause is corrected. This light does not indicate how much oil is in the engine. The engine oil level must be checked under the hood.

Oil Temperature Warning Light This warning light will illuminate to indicate the engine oil temperature is high. If the light turns on while driving, stop the vehicle and shut off the engine as soon as possible. Wait for the oil temperature to return to normal levels. Seat Belt Reminder Warning Light This warning light indicates when the driver or passenger seat belt is unbuckled. When the ignition is first placed in the ON/RUN or ACC/ON/RUN position and if the driver’s seat belt is unbuckled, a chime will sound and the light will turn on. When driving, if the driver or front passenger seat belt remains unbuckled, the Seat Belt Reminder Light will flash or remain on continuously and a chime will sound. Transmission Temperature Warning Light This warning light will illuminate to warn of a high transmission fluid temperature. This may occur with strenuous usage such as trailer towing. If this light turns on, stop the vehicle and run the engine at idle or slightly faster, with the transmission in PARK (P) or NEUTRAL (N), until the light turns off. Once the light turns off, you may continue to drive normally. WARNING! If you continue operating the vehicle when the Trans-mission Temperature Warning Light is illuminated you could cause the fluid to boil over, come in contact with hot engine or exhaust components and cause a fire. CAUTION! Continuous driving with the Transmission Temperature Warning Light illuminated will eventually cause severe transmission damage or transmission failure.

Vehicle Security Warning Light This warning light will flash at a fast rate for approximately 15 seconds when the vehicle security system is arming, and then will flash slowly until the vehicle is disarmed. Hybrid Electric Vehicle System Service Warning Light This warning light will illuminate when ser-vice to the hybrid electric system is needed. It will be accompanied by a “Service Hybrid Electric Vehicle System” warning message in the cluster. If the telltale stays on or continues to come on, contact an authorized dealer as soon as possible. Plug Status Fault Warning Light This warning light will illuminate when a plug status fault is detected (when the vehicle is not in motion). It will be accompanied by a cluster message indicating the type of fault. You may receive one of the following messages if a fault is detected:

• “Service Charging System” If you see this mes-sage, it is recommended to unplug and plug in again, or try a different charging station. If an issue continues, contact an authorized dealer to service your high-voltage charging system.
• “Issue Detected Check External Charging Station” If you see this message, the charging station may be powered off, having an internal fault or being scheduled to charge later. It is recommended to try a different charging station. If an issue continues, then contact an authorized dealer.

NOTE:

• Older or non-compliant J1772 EVSE models may not support the charging of this vehicle. If this vehicle does not charge, it may be connected to a non-compliant Level 2 EVSE and will flash indicators. Please identify this failure to the site operator and/or EVSE provider.
• Before this vehicle can be driven, the EVSE Charging Cord must be disconnected from the vehicle.

Torque Limited Warning Light

This warning light illuminates when vehicle acceleration is limited due to a reduction in engine or electric motor performance. Con-tact an authorized dealer for service if illumination persists.

YELLOW WARNING LIGHTS USER MANUAL

Anti-lock brake System (ABS) Warning Light This warning light monitors the ABS. The light will turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position and may stay on for as long as four seconds. If the ABS light remains on or turns on while driving, then the Anti-Lock portion of the brake system is not functioning and service is required as soon as possible. However, the conventional brake system will continue to operate normally, assuming the Brake Warning Light is not also on. If the ABS light does not turn on when the ignition is placed in the ON/RUN or ACC/ON/RUN position, have the brake system inspected by an authorized dealer. Adaptive Cruise Control (ACC) Fault Warning Light  This warning light will illuminate to indicate a fault in the ACC system. Contact a local authorized dealer for service. Electric Park Brake Warning Light

This warning light will illuminate to indicate the Electric Park Brake is not functioning properly and service is required. Contact an authorized dealer. Electronic Stability Control (ESC) Active Warning Light This warning light will indicate when the ESC system is Active. The ESC Indicator Light in the instrument cluster will come on when the ignition is placed in the ON/RUN or ACC/ON/ RUN position, and when ESC is activated. It should go out with the engine running. If the ESC Indicator Light comes on continuously with the engine running, a malfunction has been detected in the ESC system. If this warning light remains on after several ignition cycles, and the vehicle has been driven several miles (kilometres) at speeds greater than 30 mph (48 km/h), see an authorized dealer as soon as possible to have the prob-lem diagnosed and corrected.

• The ESC OFF Indicator Light and the ESC Indicator Light come on momentarily each time the ignition is placed in the ON/RUN or ACC/ON/RUN position.
• The ESC system will make buzzing or clicking sounds when it is active. This is normal; the sounds will stop when ESC becomes inactive.
• This light will come on when the vehicle is in an ESC event.

Electronic Stability Control (ESC) OFF Warning Light This warning light indicates the ESC is off. Each time the ignition is turned to ON/RUN or ACC/ON/RUN, the ESC system will be on, even if it was turned off previously.

Engine Check/Malfunction Indicator Warning Light

The Engine Check/Malfunction Indicator Light (MIL) is a part of an Onboard Diagnostic System called OBD II that monitors engine and automatic transmission control systems. This warning light will illuminate when the ignition is in the ON/RUN position before the engine starts. If the bulb does not come on when turning the ignition switch from OFF to ON/RUN, have the condition checked promptly? Certain conditions, such as a loose or missing gas cap, poor quality fuel, etc., may illuminate the light after the engine starts. The vehicle should be serviced if the light stays on through several typical driving styles. In most situations, the vehicle will drive normally and will not require towing. When the engine is running, the MIL may flash to alert serious conditions that could lead to immediate loss of power or severe catalytic converter damage. The vehicle should be serviced by an authorized dealer as soon as possible if this occurs.

WARNING! A malfunctioning catalytic converter can reach higher temperatures than in normal operating conditions. This can cause a fire if you drive slowly or park over flammable substances such as dry plants, wood, cardboard, etc. This could result in death or serious injury to the driver, occupants or others.

CAUTION! Prolonged driving with the Malfunction Indicator Light (MIL) on could cause damage to the vehicle control system. It also could affect fuel economy and drive-ability. If the MIL is flashing, severe catalytic converter damage and power loss will soon occur. Immediate service is required.

Fuel Level Sensor Failure Warning Light This light illuminates when there is a fuel level sensor failure. If this light illuminates, take it to an authorized dealer and have them inspect it.

LaneSense Warning Light The LaneSense Warning Light will be solid yellow when the vehicle is approaching a lane marker. The warning light will flash when the vehicle is crossing the lane marker

Low Fuel Warning Light

When the fuel level reaches approximately 1.85 gal (7 L) this warning light will turn on, and remain on until fuel is added. A single warning chime will sound with a Low Fuel Warning.

Low Washer Fluid Warning Light  This warning light will illuminate and a single chime will sound when the windshield washer fluid is low.

Service AWD Warning Light This telltale will turn on to indicate that the All Wheel Drive (AWD) system is not functioning properly and that service is required. Contact an authorized dealer.

Service Forward Collision Warning (FCW) or Pedestrian Emergency Braking (PEB) Warning Light

This warning light will illuminate to indicate a fault in the FCW or PEB Warning System. Contact an authorized dealer for service

Service LaneSense Warning Light This warning light will illuminate when the LaneSense system is not operating and requires service. Please see an authorized dealer.

Service Stop/Start System Warning Light This warning light will illuminate when the Stop/Start system is not functioning properly and service is required. Contact an authorized dealer for service.

Tire Pressure Monitoring System (TPMS) Warning Light

The warning light switches on and a mes-sage is displayed to indicate that the tyre pressure is lower than the recommended value and/or that slow pressure loss is occurring. In these cases, optimal tyre duration and fuel consumption may not be guaranteed. Should one or more tyres be in the condition previously mentioned, the display will show the indications corresponding to each tyre. CAUTION! Do not continue driving with one or more flat tyres as handling may be compromised. Stop the vehicle, avoiding sharp braking and steering. If a tyre puncture occurs, repair immediately using the dedicated tyre repair kit and contact an authorized dealer as soon as possible. Each tyre, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tyre inflation pressure label. If your vehicle has tyres of a different size than the size indicated on the vehicle placard or tyre inflation pressure label, you should determine the proper tyre inflation pressure for those tyres. As an added safety feature, your vehicle has been equipped with a TPMS that illuminates a low tyre pressure telltale when one or more of your tyres is significantly underinflated. Accordingly, when the low tyre pressure telltale illuminates, you should stop and check your tyres as soon as possible, and inflate them to the proper pressure. Driving on a significantly underinflated tire causes the tire to overheat and can lead to tire failure. Underinflation also reduces fuel efficiency and tire tread life and may affect the vehicle’s handling and stopping ability. Please note that the TPMS is not a substitute for proper tire maintenance, and it is the driver’s responsibility to maintain correct tire pressure, even if underinflation has not reached the level to trigger illumination of the TPMS low tire pressure telltale. Your vehicle has also been equipped with a TPMS malfunction indicator to indicate when the system is not operating properly. The TPMS malfunction indicator is combined with the low tire pressure telltale. When the system detects a malfunction, the telltale will flash for approximately one minute and then remain continuously illuminated. This sequence will continue upon subsequent vehicle start-ups as long as the malfunc-tion exists. When the malfunction indicator is illuminated, the system may not be able to detect or signal low tire pressure as intended. TPMS malfunctions may occur for a variety of reasons, including the installation of replacement or alternate tires or wheels on the vehicle that prevents the TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more tires or wheels on your vehicle to ensure that the replacement or alternate tires and wheels allow the TPMS to continue to function properly. CAUTION! The TPMS has been optimized for the original equip-ment tires and wheels. TPMS pressures and warnings have been established for the tire size equipped on your vehicle. Undesirable system operation or sensor damage may result when using replacement equip-ment that is not of the same size, type, and/or style. Aftermarket wheels can cause sensor damage. Using aftermarket tire sealants may cause the Tire Pressure Monitoring System (TPMS) sensor to become inoperable. After using an aftermarket tire sealant it is rec-ommended that you take your vehicle to an authorized dealer to have your sensor function checked.

YELLOW INDICATOR LIGHTS OWNER’S MANUAL

Forward Collision Warning (FCW) or Pedestrian Emergency Braking (PEB) OFF Indicator Light  This indicator light illuminates to indicate that Forward Collision Warning (FCW) or Pedestrian Emergency Braking (PEB) is off.

GREEN INDICATOR LIGHTS

Adaptive Cruise Control (ACC) Set With Target Vehicle Detected Indicator Light This indicator light will illuminate when the Adaptive Cruise Control speed is SET and the vehicle in front is detected.

Adaptive Cruise Control (ACC) Set With No Target Detected

Indicator Light 

This indicator light will illuminate when the Adaptive Cruise Control speed is SET and there is no vehicle in front detected.

Cruise Control Set Indicator Light This indicator light will illuminate when the cruise control is set to the desired speed.

Front Fog Indicator Light  This indicator light will illuminate when the front fog lights are on.

 

LaneSense Indicator Light The LaneSense indicator light illuminates solid green when both lane markings have been detected and the system is armed and ready to provide visual and torque warnings if an unintentional lane departure occurs

Parking/Headlights On Indicator Light This indicator light will illuminate when the parking lights or headlights are turned on.

Stop/Start Active Indicator Light  This indicator light will illuminate when the Stop/Start function is in “Autostop” mode

Turn Signal Indicator Lights

When the left or right turn signal is activated, the turn signal indicator will flash indepen-dently and the corresponding exterior turn signal lamps will flash. Turn signals can be activated when the multifunction lever is moved down (left) or up (right).

NOTE:

• A continuous chime will sound if the vehicle is driven more than 1 mile (1.6 km) with either turn signal on.
• Check for an inoperative outside light bulb if either indicator flashes at a rapid rate.

Max Regeneration Indicator Light This indicator light will illuminate to indicate that Max Regeneration is on and capable.` When the switch is pressed, the following instrument cluster messages will be seen:

• “Max Regeneration On”: appears when the feature is turned on.
• “Max Regeneration Off”: appears when the feature is turned off.
• “Max Regeneration Unavailable”: appears when the feature is requested, but the vehicle is unable to comply. The LED will flash for five seconds to indicate unavailability

Ready To Drive Indicator Light This indicator light will illuminate to indicate that the vehicle has enough power to be driven, regardless of the speed of the vehicle.

Plug Status Indicator Light When plugged in, the green plug indicator light will illuminate if the EVSE charging plug is securely attached to the charging port. This indicates that the plug is detected, but doesn’t mean it is charging. It will be accompanied by a cluster message indicating the charge status:

• “Plugged In And Charging”
• “Plugged In And Waiting to Charge On A Set Schedule”
• “Plugged in and Charging Complete”

NOTE: The vehicle cannot be driven until it is unplugged.

WHITE INDICATOR LIGHTS USER MANUAL

Adaptive Cruise Control (ACC) Ready Light This indicator light will illuminate when the vehicle equipped with ACC has been turned on but not set.

Cruise Control Ready Indicator Light This indicator light will illuminate when the cruise control is ready, but not set.

LaneSense Indicator Light When the LaneSense system is ON, but not armed, the LaneSense indicator light illumi-nates solid white. This occurs when only the left, right, or neither lane line has been detected. If a single lane line is detected, the system is ready to provide only visual warnings if an unintentional lane departure occurs on the detected lane line

Set Speed Display Indicator Light The Set Speed Display indicator light indicates the set speed for the Cruise Control and Adaptive Cruise Control (ACC) settings.

BLUE INDICATOR LIGHTS

High Beam Indicator Light This indicator light will illuminate to indicate that the high-beam headlights are on. With the low beams activated, push the multifunction lever forward (toward the front of the vehicle) to turn on the high beams. Pull the multifunction lever rearward (toward the rear of the vehicle) to turn off the high beams. If the high beams are off, pull the lever toward you for a temporary high beam on, “flash to pass” scenario. ONBOARD DIAGNOSTIC SYSTEM OBD II Your vehicle is equipped with a sophisticated Onboard Diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic transmission control systems. When these systems are operating properly, your vehicle will provide excellent performance and fuel economy, as well as emissions well within current government regulations. If any of these systems require service, the OBD II sys-tem will turn on the Malfunction Indicator Light (MIL). It will also store diagnostic codes and other information to assist your service technician in making repairs. Although your vehicle will usually be drivable and not need towing, see an authorized dealer for service as soon as possible.

FAQs

Useful Link

2023 – 2024 Chrysler Pacifica Plug-in Hybrid Specs, Price, Features, Mileage and Review

2024 Chrysler Pacifica Instrument Cluster User Guide

Video: 2024 Chrysler Pacifica Warning Lights