2024 Honda CR-V Warning Lights and Indicator User Guide

• Comes on when the parking brake is applied, and goes off when it is released.

• The beeper sounds and the indicator comes on if you drive with the parking brake applied.
• Comes on for about 30 seconds when you apply the electric parking brake while the power mode is in ACCESSORY or VEHICLE OFF, then goes off.
• Stays on for about 30 seconds when you set the power mode to VEHICLE OFF while the electric parking brake is applied, then goes off.

• Comes on when the brake fluid level is low.

• Comes on while driving – Make sure the parking brake is released. Stop in a safe place and check the brake fluid level.

• Comes on if there is a problem with the brake system.

• Comes on along with the Parking Brake and Brake System Indicator (amber) – Immediately stop in a safe place. Contact a dealer for repair. The brake pedal becomes harder to operate.

Depress the pedal further than you normally do.

• Comes on along with the ABS indicator – Havey our vehicle checked by a dealer.
• Blinks and the Parking Brake and Brake System

Indicator (amber) comes on at the same time – There is a problem with the electric parking brake system. The parking brake may not be set.

Avoid using the parking brake and have your vehicle checked by a dealer immediately.

• Comes on if there is a problem with a system related to braking other than the conventional brake system.

• Comes on while driving – Avoid high speeds and sudden braking. Take the vehicle to a dealer immediately.

• Comes on if there is a problem with the electric parking brake system and/or the automatic brake hold system.

• Stays on constantly – Avoid using the parking brake and have your vehicle checked by a dealer immediately.

• Comes on if there is a problem with the radar sensor.
• Indicator may come on temporarily when the Maximum Load Limit is exceeded.

• Make sure the total load is within the Maximum Load Limit.
• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if the brake system is deactivated temporarily after the battery has been disconnected, then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Comes on when the automatic brake hold system is on.

• Comes on when the automatic brake hold is activated.

• Readiness codes are part of the on-board diagnostics for the emissions control systems.

• Comes on if there is a problem with the emissions control systems.
• Blinks when a misfire in the engine’s cylinders is detected.

• Comes on when there is a problem with the charging system.

• Stop in a safe place and contact a dealer immediately.

• Indicates the current shift position.

• Blinks if the transmission system has a problem.

• Have your vehicle checked by a dealer immediately.

• Blinks and the beeper sounds for a few seconds if you are not wearing a seat belt when you set the power mode to ON, then the indicator comes on.
• If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later.
• Comes on for a while when the rear seat belt is unfastened while the power mode in ON.
• Blinks while driving if you and/or any passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.

• The beeper stops and the indicator goes off when you and the passengers fasten their seat belts.
• Stays on after you and/or the passengers have fastened the seat belt(s) – A detection error may have occurred in the sensor. Have your vehicle checked by a dealer.

• Comes on when the fuel reserve is running low (approximately 2.1 U.S. gal./8.0 Liter left).

• Comes on – Refuel your vehicle as soon as possible.

• Blinks if there is a problem with the fuel gauge.

• Have your vehicle checked by a dealer.

• Comes on when the engine coolant temperature is low.

• If the indicator stays on after the engine has reached normal operating temperature, there may be a problem with the temperature sensors. Have your vehicle inspected by a dealer.

• Comes on if there is a problem with the ABS.

• Stays on constantly – Have your vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.

• Comes on if a problem with any of the following is detected:
  • Supplemental Restraint System
  • Side airbag system
  • Side curtain airbag system
  • Seat belt tensioner

• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if there is a problem with the EPS system.

• Stays on constantly – Have your vehicle checked by a dealer.
• Do not drive displays on the driver information interface – Immediately stop in a safe place and contact a dealer.

• Blinks when VSA® is active.

• Comes on if there is a problem with the VSA® system, brake assist system, hill start assist system, starting assist brake function, or agile handling assist.

• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if the VSA® system is deactivated temporarily after the battery has been disconnected, then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Comes on when you partially disable VSA®.

• May come on briefly if the power mode is set to ON and the vehicle is not moved within 45 seconds, to indicate the calibration process is not yet complete.
• Comes on and stays on when:
  • One or more tires’ pressures are determined to be significantly low.
  • The system has not been calibrated.

• Comes on while driving – Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.
• Stays on after the tires are inflated to the recommended pressures – The system needs to be calibrated.

• Blinks for about one minute, and then stays on if there is a problem with the TPMS, or when a compact spare tire is temporarily installed.

• Blinks and remains on – Have your vehicle checked by a dealer. If the vehicle is fitted with a compact spare tire, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.

• Comes on if the TPMS is deactivated temporarily after the battery has been disconnected, then reconnected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Blinks when you operate the turn signal lever.
• Blinks along with all turn signals when you press the hazard warning button.

• Does not blink or blinks rapidly

• Comes on when the parking, tail, and other external lights are on.

• Comes on when the high beam headlights are on.

—

• Comes on when all the operating conditions of the auto high-beam are met.

• Blinks if the immobilizer system cannot recognize the key information.

• Blinks – You cannot start the engine. Set the power mode to VEHICLE OFF*1, then select the ON mode again.
• Repeatedly blinks – The system may be malfunctioning. Have your vehicle checked by a dealer.
• Do not attempt to alter this system or add other devices to it. Electrical problems can occur.

• Blinks when the security system alarm has been set.

• Comes on when you set the drive mode to ECON.

• Comes on when you set the drive mode to NORMAL.

•  Comes on when you set the drive mode to

SNOW.

• Lights up in white when the hill descent control system is on and ready to use.
• Lights up in green when the hill descent control system is in operation.

• Comes on along with a beep when a problem is detected. A system message on the driver information interface appears at the same time.

• While the indicator is on, press the (home) button, and select Warnings to see the message again.
• Refer to the Indicators information in this chapter when a system message appears on the driver information interface. Take the appropriate action for the message.
• The driver information interface will not return to the normal screen unless the warning is canceled, or the (home) button is pressed.

Auto Idle Stop OFF

Indicator

• Comes on when the Auto Idle Stop system has been turned off by the Auto Idle Stop OFF button.

• Blinks if there is a problem with the Auto Idle Stop system.

• Blinks – Have your vehicle checked by a dealer.

• Comes on when Auto Idle Stop is in operation. The engine automatically shuts off.

• Comes on while Auto Idle Stop is temporarily suspended in the following situations.

• Brake pedal is not fully pressed

• Depress the brake pedal firmly.

• The transmission is in a position other than (D

• System charging is prioritized

• Climate control system is prioritized

• Engine coolant temperature is not in operating range

• SNOW mode is selected.

• The battery temperature is too low.

• Auto Idle Stop does not activate for some reason.

• If you press and hold the Auto Idle Stop OFF button, you can select whether to display the status messages or not.

• Comes on if there is a problem with ACC with Low Speed Follow.

• Comes on while driving – Have your vehicle checked by a dealer.

• Indicator may come on temporarily when the Maximum Load Limit is exceeded.
• ACC with Low Speed Follow has been automatically canceled.

• Make sure the total load is within the Maximum Load Limit.
• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if the ACC with Low Speed Follow is deactivated temporarily after the battery has been disconnected, then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Lights up in white when you press the button.
• Lights up in green when you press the

RES/+/SET/− switch up or down.

• Lights up in white when you change to cruise mode.
• Lights up in green when you have set a speed for cruise control.

Lane Keeping Assist System (LKAS) Indicator (Amber)

• Comes on if there is a problem with the LKAS.

• Stays on constantly – Have your vehicle checked by a dealer.

• Indicator may come on temporarily when the Maximum Load Limit is exceeded.

• Make sure the total load is within the Maximum Load Limit.
• Stays on constantly – Have your vehicle checked by a dealer.

• Lights up in white when you press the LKAS button.
• Lights up in green when the LKAS is in operation.

• Comes on if there is a problem with the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, or blind spot information system*.

• Stays on constantly – Have your vehicle checked by a dealer.

 Models with Parking Sensor System

• Comes on if there is a problem with the parking sensor.

• Check if the area around the sensor(s) is covered with mud, ice, snow, etc. If the indicator stays on even after you clean the area, have the system checked by a dealer.

• Indicator may come on temporarily when the Maximum Load Limit is exceeded.

• Make sure the total load is within the Maximum Load Limit.
• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on if the Road Departure Mitigation system, CMBSTM and Low Speed Braking Control* are deactivated temporarily after the battery has been disconnected and then re-connected.

• Drive a short distance at more than 12 mph (20 km/h). The indicator should go off. If it does not, have your vehicle checked by a dealer.

• Comes on when the Road Departure Mitigation system and/or CMBSTM shuts itself off.

• Indicator may come on temporarily if the radar sensor cannot detect any objects when passing through an enclosed space such as a tunnel, or driving on an open road without any structures nearby.
• The area around the radar sensor is blocked by dirt, mud, etc. Stop your vehicle in a safe place and wipe the debris off with a soft cloth. Indicator may take some time to go off after the radar sensor is cleaned.
• Have your vehicle checked by a dealer if the indicator does not go off even after you have cleaned the radar sensor.

• Stays on – The temperature inside the camera is too high.

Use the climate control system to cool down the camera.

The system activates when the temperature inside the camera cools down.

• Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place and wipe the debris off with a soft cloth.
• Have your vehicle checked by a dealer if the indicator and message are still displayed even after you have cleaned the area around the camera.
• It may come on when the ambient conditions are dark, such as when driving in a tunnel, or at night, dawn, or dusk.

 Models with Low Speed Braking Control

• Comes on when mud, snow, or ice accumulates in the vicinity of the sonar sensor.

• Remove the obstacle in the vicinity of the sonar sensor.

 Models with blind spot information system

• Comes on when mud, snow, or ice accumulates in the vicinity of the blind spot information system sensor.
• Comes on when the temperature of the blind spot information system sensor is high.

• Comes on while driving – Something may be interfering with the blind spot information system sensor. Check the vicinity of the blind spot information system sensor and remove any obstacles.
• The system will return to normal when the temperature cools down.

• Lights up in green when the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, Parking Sensor System*, and blind spot information system* are on.
• Lights up in green and gray when the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, Parking Sensor System*, or blind spot information system*, or any two, three or four of these systems are off.
• Lights up in gray when the Road Departure Mitigation system, CMBSTM, Low Speed Braking Control*, Parking Sensor System*, and blind spot information system* are off.