Indicator

Name

On/Blinking

Explanation

Message

Transmission System Indicator

●  The indicated current gear selection blinks if there is a problem with the transmission system.

●  Avoid sudden starts and acceleration, and stop in a safe place immediately. Have your vehicle checked by a dealer.

•  All the gear positions may light for several seconds, and go off.

• When all the gear positions light, immediately stop your vehicle in a safe place.
• Indicators go off if there is no problem. However, even if they go off, take your vehicle to a dealer for inspection.

●  The indicated current gear selection or all the gear positions blink if there is a problem with the transmission system, and the vehicle no longer moves.

• Immediately stop in a safe place.

2 Emergency Towing

• Have your vehicle checked by a dealer.

•   The indicated current gear selection or all the gear positions blink if you cannot select (P due to the transmission system failure.

•  The engine can be activated as a temporary measure.

2 If the Transmission Indicator Blinks along with the Warning Message 

●  Set the parking brake when parking.

●  Have your vehicle checked by a dealer immediately.

Indicator

Name

On/Blinking

Explanation

Message

Seat Belt Reminder Indicator

• Blinks and the beeper sounds for a few seconds if you are not wearing a seat belt when you set the power mode to ON, then the indicator comes on.
•  If the front passenger is not wearing a seat belt, the indicator comes on a few seconds later.
• Comes on for a while when the rear seat belt is unfastened while the power mode in ON.
• Blinks while driving if you and/or any passenger has not fastened a seat belt. The beeper sounds and the indicator blinks at regular intervals.

• The beeper stops and the indicator goes off when you and the passengers fasten their seat belts.
• Stays on after you and/or the passengers have fastened the seat belt(s) – A detection error may have occurred in the sensor. Have your vehicle checked by a dealer.

2 Seat Belt Reminder 

Low Fuel Indicator

• Comes on when the fuel reserve is running low (approximately 2.5

U.S. gal./9.5 Liter left).

• Blinks   if there is a problem with the fuel gauge.

• Comes on – Refuel your vehicle as soon as possible.
• Blinks – Have your vehicle checked by a dealer.

Anti-lock Brake System (ABS) Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
•  If it comes on at any other time, there is a problem with the ABS.

Stays on constantly – Have your vehicle checked by a dealer. With this indicator on, your vehicle still has normal braking ability but no anti-lock function.

2 Anti-lock Brake System (ABS) 

Indicator

Name

On/Blinking

Explanation

Message

Supplemental Restraint System Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
•  Comes on if a problem with any of the following is detected:
• Supplemental

Restraint System

• Side airbag system
• Side curtain airbag system
•  Seat belt tensioner

• Stays on constantly or does not come on at all – Have your vehicle checked by a dealer.

Vehicle Stability AssistTM (VSA®) System Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Blinks when VSA® or trailer stability

assist is active.

• Comes on if there is a problem with the VSA®, hill start assist, trailer stability assist or brake lighting system.

• Stays on constantly – Have your vehicle checked by a dealer.

2 Vehicle Stability Assist TM (VSA®), aka Electronic Stability Control (ESC), System 

2 Trailer Stability Assist 

2 Hill start assist system 

• When Trailer Stability Assist Problem is displayed on the Driver Information Interface, the VSA® does not activate.

Indicator

Name

On/Blinking

Explanation

Message

Vehicle Stability AssistTM (VSA®) OFF Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.

—

—

Comes on when VSA® OFF switch is pressed.

• Appears when Normal or Snow mode is selected.

2 VSA® On and Off 

• Comes on when Mud/Sand mode is selected by pressing Intelligent Traction Management System switch.

• Appears when Mud mode is selected.

2 Intelligent Traction Management

• Appears when Sand mode is selected.

2 Intelligent Traction Management

•  Comes on when VSA® OFF switch is pressed.

Appears when Mud or Sand mode is selected.

2 VSA® On and Off 

Electric Power Steering (EPS) System Indicator

• Comes on when you set the power mode to ON, and goes off when the engine starts.

Comes on if there is a problem with the EPS system.

• Stays on constantly or does not come on at all – Have your vehicle checked by a dealer.

2 If the Electric Power Steering (EPS) System Indicator Comes On 

Indicator

Name

On/Blinking

Explanation

Message

Low Tire Pressure/TPMS Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Comes on if the tire pressure of any of the tires becomes significantly low.

• Comes on while driving 
  • Stop in a safe place, check tire pressures, and inflate the tire(s) if necessary.

• Blinks for about one minute, and then stays on if there is a problem with the TPMS with Tire Fill Assist, or when a compact spare tire is temporarily installed.

• Blinks and remains on – Have your vehicle checked by a dealer. If the vehicle is fitted with a compact spare, get your regular tire repaired or replaced and put back on your vehicle as soon as you can.

Turn Signal and Hazard Warning Indicators

• Blinks when you operate the turn signal lever.

•  Blinks along with all turn signals when you press the hazard warning button.

•  Does not blink or blinks rapidly

2 Replacing Light Bulbs 

—

Lights On Indicator

• Comes on whenever the light switch is on, or in AUTO when the exterior lights are on.

•   If you set the power mode to ACCESSORY or VEHICLE OFF while the exterior lights are on, a chime sounds when the driver’s door is opened.

—

High Beam Indicator

•  Comes on when the high beam headlights are on.

—

—

Indicator

Name

On/Blinking

Explanation

Message

Autog High-Beam Indicator

•  Comes on for a few seconds when you set the power mode to ON, then goes off.

•  Comes on when all the operating conditions of the auto high-beam are met.

2 Auto High-Beam 

—

Fog Light Indicator*

•  Comes on when the fog lights are on.

—

—

Immobilizer System Indicator

• Comes on briefly when you set the power mode to ON, then goes off.

•  Blinks if the immobilizer system cannot recognize the key information.

• Blinks – You cannot start the engine. Set the power mode to VEHICLE OFF*1, then select the ON mode again.

•  Repeatedly blinks – The system may be malfunctioning. Have your vehicle checked by a dealer.

•  Do not attempt to alter this system or add other devices to it. Electrical problems can occur.

—

Security System Alarm Indicator

•  Comes on briefly when you set the power mode to ON, then goes off.

•  Blinks when the security system alarm has been set.

2 Security System Alarm 

—

Indicator

Name

On/Blinking

Explanation

Message

System Message Indicator

• Comes on along with a beep when a problem is detected. A system message on the driver information interface appears at the same time.

• While the indicator is on, press the  (home) button, select Warnings, then press the ENTER button to see the message again.

•  Refer to the Indicators information in this chapter when a system message appears on the driver information interface. Take the appropriate action for the message.

• The driver information interface does not return to the normal screen unless the warning is canceled, or the ENTER button is pressed repeatedly.

—

ECON Mode Indicator

• Comes on when the ECON mode is on.

2 ECON Mode 

Intelligent Traction Management Indicator

• Comes on when pressing the Intelligent Traction Management button.

2 Intelligent Traction Management

Indicator

Name

On/Blinking

Explanation

Message

Auto Idle Stop Indicator (Green)

Comes on when Auto Idle Stop is in operation. The engine automatically shuts off.

2 Auto Idle Stop 

—

Auto Idle Stop

OFF Indicator

• Comes on when the Auto Idle Stop system has been turned off by the Auto Idle Stop system OFF button.

2 Auto Idle Stop System ON/OFF

 Auto Idle Stop System Indicator (Amber)

• Comes on for a few seconds when you set the power mode to ON, then goes off.

—

—

• Blinks if there is a problem with the Auto Idle Stop system.

•  Have your vehicle checked by a dealer.

Auto Idle Stop Suspend Indicator

• Comes on while Auto Idle Stop is temporarily suspended in the following situations.

—

—

• Brake pedal is not fully pressed.

• Depress the brake pedal firmly.

Indicator

Name

On/Blinking

Explanation

Message

Auto Idle Stop Suspend Indicator

• The transmission is in a position other than (D.

2 Auto Idle Stop 

•  System charging is prioritized.

• Climate control system is prioritized.
• is ON (indicator on).

• Engine coolant temperature is not in operating range.

• The Intelligent Traction Management is set to Snow, Mud, or Sand.

• The battery temperature is too low.
•  Auto Idle Stop does not activate for some reason.

—

•  If you press and hold the Auto Idle Stop OFF button, you can select whether to display the status messages or not.

Indicator

Name

On/Blinking

Explanation

Message

All-wheel drive (AWD) Indicator

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Comes on if there is a problem with the AWD system.
• Blinks when the differential temperature is too high.

• Stays on constantly – The engine drives the front wheels only in this state. Have your vehicle checked by a dealer.

• Blinks while driving – Stop in a safe place, change to (P, and idle the engine until the indicator goes off. If the indicator does not stop blinking, take your vehicle to a dealer.

2 Intelligent Variable Torque Management (i-VTM4TM) AWD System 

Lane Keeping Assist System (LKAS) Indicator (Amber)

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Comes on if there is a problem with the LKAS.

• Stays on constantly – Have your vehicle checked by a dealer.

Lane Keeping Assist System (LKAS) Indicator (Green)

• Comes on when you press the

MAIN button.

2 Lane Keeping Assist System (LKAS)

—

Indicator

Name

On/Blinking

Explanation

Message

Road Departure Mitigation (RDM) Indicator

• Comes on for a few seconds when you change the power mode to ON, then goes off.
•  Comes on if there is a problem with the RDM system.

• Stays on constantly – Have your vehicle checked by a dealer.

• Comes on when the RDM system shuts itself off.

• Stays on – The temperature inside the camera is too high.

Use the climate control system to cool down the camera.

The system activates when the temperature inside the camera cools down.

2 Front Sensor Camera 

• Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.
• Have your vehicle checked by a dealer if the indicator and message come back on after you cleaned the area around the camera.

2 Front Sensor Camera 

Indicator

Name

On/Blinking

Explanation

Message

Adaptive Cruise Control (ACC) Indicator (Amber)

• Comes on for a few seconds when you set the power mode to ON, then goes off.
• Comes on if there is a problem with ACC.

• Comes on while driving – Have your vehicle checked by a dealer.

Adaptive Cruise Control (ACC) Indicator (Green)

• Comes on when you press the

MAIN button.

2 Adaptive Cruise Control (ACC)

—

Collision Mitigation Braking System TM (CMBSTM)

Indicator

• Comes on for a few seconds when you change the power mode to ON, then goes off.
• Comes on when you deactivate the CMBSTM. A driver information interface message appears for five seconds.
•   Comes on if there is a problem with the CMBSTM.

• Stays on constantly without the CMBSTM off – Have your vehicle checked by a dealer.

2 Collision Mitigation Braking SystemTM (CMBSTM) 

Indicator

Name

On/Blinking

Explanation

Message

Collision Mitigation Braking SystemTM (CMBSTM)

Indicator

• Comes on when the CMBSTM shuts off.

• Stays on – The temperature inside the camera is too high. Use the climate control system to cool down the camera. The system activates when the temperature inside the camera cools down.

2 Front Sensor Camera 

•  Stays on – The area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.

• Have your vehicle checked by a dealer if the indicator does not go off even after you cleaned the camera.

2 Front Sensor Camera 

• When the radar sensor gets dirty, stop your vehicle in a safe place, and wipe off dirt using a soft cloth. Indicator may take some time to go off after the radar sensor is cleaned.
• Have your vehicle checked by a dealer if the indicator does not go off even after you clean the sensor cover.

2 Radar Sensor 

Indicator

Name

On/Blinking

Explanation

Message

Blind spot information System Indicator

• Stays on while blind spot information system is turned off.

—

• Comes on when mud, snow, or ice accumulates in the vicinity of sensor.

Comes on while driving – Remove the obstacle in the vicinity of the sensor.

2 Blind spot information System.

•  Comes on if there is a problem with the system.

•  Comes on while driving – Have your vehicle checked by a dealer.

Message

Condition

Explanation

• Appears if any door or the tailgate is not completely closed.

• Goes off when all doors and the tailgate are closed.

• Appears when the hood is opened.

• Close the hood.

•  Appears when the engine oil pressure is low.

•  Appears while driving – Immediately stop in a safe place.

2 If the Engine Oil Low Warning Appears 

• Appears when the washer fluid is low.

• Refill the washer fluid.

2 Refilling Window Washer Fluid 

•  Appears when the temperature of the transmission is starting to get too hot.

•  The performance of the vehicle may be reduced.

• Until the message disappears, reduce your speed and allow the system to cool down.

• Appears if the battery charge becomes low.

• Charge the battery.

Message

Condition

Explanation

•  Appears when there is a problem with the sensor on the battery.

• Have your vehicle checked by a dealer.

2 Checking the Battery 

• Appears when the scheduled maintenance is due soon.

•  Consequently, Maintenance Due Now and

Maintenance Past Due follow.

2 Maintenance Minder Messages on the Driver 

• Appears when the engine coolant temperature gets abnormally high.

2 Overheating 

U.S.

Canada

•  Appears when there is a problem with the power tailgate system.

•  Manually open or close the power tailgate.

•  Have your vehicle checked by a dealer.

U.S.

Canada

• Appears when the starter system has a problem.

As a temporary measure, press and hold the ENGINE START/STOP button for up to 15 seconds while pressing the brake pedal and manually start the engine.

• Have your vehicle checked by a dealer.

Message

Condition

Explanation

Canada

•  Appears when the steering wheel is locked.

•  Move the steering wheel left and right while pressing the ENGINE START/STOP button.

• Appears when the power mode is in ACCESSORY.

—

• Appears after the driver’s door is opened when the power mode is in ACCESSORY.

•  Change the power mode to VEHICLE OFF.

2 ENGINE START/STOP Button 

• Appears when you close the door with the power mode in ON without the remote inside the vehicle.

• Disappears when you bring the remote back inside the vehicle and close the door.

•  Appears when the remote battery becomes weak.

• Replace the battery as soon as possible.

• Appears if the remote battery is too weak to start the engine or the key is not within operating range to start the engine.

A beeper sounds six times.

• Bring the remote in front of the ENGINE START/STOP

button to be touched with.

• Appears three seconds after the To Start, Hold Remote Near Start Button, then To Start Engine messages appeared sequentially.

•  Unless you bring the keyless remote in front of the ENGINE START/STOP button, this message does not appear.

Message

Condition

Explanation

• Appears if there is a problem with the cooling system.

• Drive slowly to prevent overheating and have your vehicle checked by a dealer as soon as possible.

• Appears if there is a problem with the headlights.

• Appears while driving – The headlights may not be on. When conditions allow you to drive safety, have your vehicle checked by a dealer as soon as possible.

 Models with parking sensor system

•  Appears if there is a problem with the parking sensor system.

9Check if the area around the sensor(s) is covered with mud, ice, snow, etc. If the indicator(s) stays on or the beeper does not stop even after you clean the area, have the system checked by a dealer.

 Models with parking sensor system

•  Appears if there are obstacles around the sensors.

• Check for obstacles near your vehicle to make sure it is safe to park.

• Appears as soon as a problem is detected in the keyless access system.

• Appears constantly – Have your vehicle checked by a dealer.

• Appears as soon as a problem is detected in the push button starting system.

• Appears constantly – Have your vehicle checked by a dealer.

• Appears if you press the ENGINE START/STOP

button while the vehicle is moving.

2 Emergency Engine Stop 

Message

Condition

Explanation

• Appears if there is a problem with the Auto high- beam.

•  Manually operate the headlight switch.
• If you are driving with the high-beam headlights when this happens, the headlights are changed to low beams.

• Appears when the area around the camera is blocked by dirt, mud, etc. Stop your vehicle in a safe place, and wipe it off with a soft cloth.
• May appear when driving in bad weather (rain, snow, fog, etc.)

• Have your vehicle checked by a dealer if the message comes back on after you cleaned the area around the camera.

• Flashes when the system senses a likely collision with a vehicle in front of you.

•  Take the appropriate means to prevent a collision (apply the brakes, change lanes, etc.)

• Appears when ACC has been automatically canceled.

• You can resume the set speed after the condition that caused ACC to cancel improves. Press the RES/+ button.

• Appears when pressing the –/SET button while the vehicle is moving, and the brake pedal is depressed.

•  ACC cannot be set.

• Appears if the VSA® or traction control function operates while ACC is in operation.

• ACC has been automatically canceled.